background image

ACORN ENGINEERING FIELD SERVICE

TOLL FREE

 800-743-8259 • 

LOCAL

  626-855-4866 • 

FAX

 626-855-4863

INSTALLATION, OPERATIONS & MAINTENANCE MANUAL

Please visit 

www.acorneng.com

for most current specifications.

TROUBLE SHOOTING FOR 9 VOLT DC SENSOR OPERATED VALVES 

Normal Valve Function: 

9 Volt DC sensor operated valve has flow time of 90 seconds maximum. 

To reactivate, the user must move out of and return to the sensing area. 

CONDITION: 

WATER DOES NOT FLOW

Indicators

Probable Cause

 

Solution

Sensor flashes continuously 
every 2 seconds when 
hands are within range. 

Low battery warning 

Replace battery 

Circuit breaker tripped. 

Reset circuit breaker 
Replace battery

Defective 9V DC transformer

Transformer polarity crossed

Replace transformer (sensor may be 
damaged and need replacement). 

Unit is in “Security Mode” after 
90 seconds of constant detection. 

Remove sources of detection and 

wait 30 seconds before checking. 

Range is too short. 

Increase range. 

Range is too long. 

Decrease range and wait 30 seconds. 

Sensor is picking up a highly 
reflective surface. 

Eliminate cause of reflection and wait 
30 seconds before checking. 

Sensor does not flash 
when the user’s hands 
are within range. 

 

Defective sensor. 

Replace sensor. 

Stops or water main closed.
Bad sensor to solenoid connection.

Debris or scale in
solenoid assembly. 

Remove solenoid, pull out plunger 

and spring, and clean with scale 

remover solution or pressurized air. 

Debris or scale in diaphragm.

 

Remove diaphragm and clean 

Sensor flashes once

when user’s hands are

within range.

 
 

Remove strainer and clean. 

CONDITION:

 FALSE TRIGGERING;

WATER FLOWS CONTINUOUSLY

Indicators

Probable Cause

 

Solution

Remove diaphragm and clean. 

Sensor flashes when user’s

hands are within range. 

Diaphragm is defective or torn.

Sensor is dirty or covered. 

Clean or uncover sensor and 

wait 30 seconds. 

Decrease range and wait 30 seconds. 

Sensor does not flash when

users hands are within range.

Range too long or highly 
reflective surface, sunlight, bright 
lights etc. are triggering sensor. 

Eliminate cause of reflection or
correct lighting problem. 

CONDITION:

 WATER FLOWS

CONTINUOUSLY BUT STOPS
WHEN HANDS ARE WITHIN RANGE

Indicators

Probable Cause

 

Solution

Water runs continuously when 
sensor not activated. Sensor 
flashes when hands are within 
range and water shuts off. 

Solenoid polarity crossed. 

Disconnect solenoid and 

reverse polarity. 

Battery completely used up.

Replace transformer. 

Open stops or water main. 
Ensure wires make proper contact. 

Debris or scale in strainer.

Replace diaphragm. 

Debris or scale in diaphragm

®

MERIDIAN  3791-LO

Part #: 9927-140-001

Page 20 of 28

Date: 03/06/19

Summary of Contents for Meridian 3791-LO





























Reviews: