background image

IMPORTANT

This fixture is intended to dispense water that has been lowered in temperature, but otherwise remains 
unchanged by the materials in the water cooler. It is common for electrical equipment to be grounded 
to water lines either within a structure or away from it. Every attempt should be made to prevent this 
kind of grounding from generating electrical feedback into the water cooler creating electrolysis. 
Electrolysis will cause a metallic taste or cause water metal content to increase.

NOTICE

A dielectric coupling must be used to connect the water cooler to the water supply . A nonmetallic 
coupler is furnished with this water cooler to meet this requirement.

ROUGHING-IN AND DIMENSIONAL DRAWING

Prior to roughing consult with local, state, and federal codes for proper mounting height.

A171408B Wall Mounted Drinking Fountain

Note: There are no mounting changes to be made for -SO models.

 

 

NOTES:

 Dimensions indicated ** are for ADA frontal approach installation. Adjust vertical dimension ** 

as required to comply with federal, state, and local codes. For Child ADA compliant parallel approach, 
decrease spout height to 30” maximum above finished floor. Provide clear floor space as required. 

ACORN ENGINEERING FIELD SERVICE

TOLL FREE

 800-743-8259 • 

LOCAL

  626-855-4866 • 

FAX

 626-855-4863

7020-904-001

Page 2 of 11

AIR FLOW

A. 3/8" NCT SUPPLY INLET

B.  WASTE OUTLET FOR 1-1/4" P-TRAP BY OTHERS.
C. ELECTRICAL SERVICE ROUGH.
D. Ø3/8" HANGER BRACKET PUNCHING, 3 PLACES FOR ANCHORING HARDWARE BY OTHERS.
E. Ø1/4" PUNCHING, 2 PLACES FOR ANCHORING HARDWARE BY OTHERS.

 GENERAL NOTES:
 1. ALL DIMENSIONS ARE IN INCHES [MM].
*2. VERTICAL DIMENSIONS INDICATED **ARE FOR ADA FRONT APPROACH; ADJUST VERTICAL DIMENSIONS AS

NECESSARY TO COMPLY WITH FEDERAL, STATE, OR LOCAL CODES.

 3. STOP VALVE, TRAP, & ELECTRICAL J-BOX ARE PROVIDED BY INSTALLER.
 4. IMPORTANT: COOLERS MUST BE ATTACHED TO WALL WITH ANCHOR SCREWS.

11"

16

5
8

"

3

7
8

"

13

1
2

"

20

3
4

"

5

1
4

"

7

7
8

"

D

C

B

A

7

1
4

"

1

3
8

"

6"

12"

TAIL

PIECE

*33"

*15

5
8

"

E

4

1
4

"

2

1
4

"

18

1
2

"

Date: 03/12/15

Please visit 

 

for most current specifications.

www.acorndrinkingfountains.com

 

INSTALLATION, OPERATIONS & MAINTENANCE MANUAL

Summary of Contents for A171.8 Series












Reviews: