background image

 
 

140 ~ 181 
182 ~ 189 
190 ~ 231 
232 ~ 239 
240 ~ 247 
248 ~ 255

 

Slow Open Fast Close 

Open 

Slow Close Fast Open 

Open 

Random Strobe 

Open

 

 

 

 

  4.4. DMX512 Connections   

The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels.   

 

 

 

1.

 

At last unit, the DMX cable has to be terminated with a terminator. Solder a 120-ohm 1/4W 

resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it in the 

DMX-output of the last unit. 

2.

 

Connect the unit together in a “daisy chain” by XLR plug cable from the output of the unit to 

the input of the next unit. The cable cannot be branched or split to a “Y” cable. DMX 512 is a 

very high-speed signal. Inadequate or damaged cables, soldered joints or corroded connectors 

can easily distort the signal and shut down the system. 

3.

 

The DMX output and input connectors are pass-through to maintain the DMX circuit, when 

one of the units’ power is disconnected. 

4.

 

Each lighting unit needs to have a DMX address to receive the data by the controller. The 

address number is between 0-511 (usually 0 & 1 are equal to 1). 

 

11B 

Summary of Contents for LP-F200 CW

















Reviews: