ACME LED-MTX25 IP User Manual Download Page 2

Page: 2 / 20

Contents

1. Safety Instructions..........................................................................................2

2. Technical Specifications..................................................................................3

3. Installation......................................................................................................4

3.1 Fixture Jointing..........................................................................................4

4. How to set the unit ........................................................................................5

4.1 Rear Panel.................................................................................................5

4.2 Main Function...........................................................................................6

5. How To Control The Unit .............................................................................10

5.1 Master/Slave Built In Preprogrammed Function ......................................10

5.2 DMX Controller ......................................................................................10

5.3 DMX512 Configuration...........................................................................11

6. DMX512 Connections ..................................................................................15

7. Troubleshooting............................................................................................16

8. Fixture Cleaning............................................................................................17

Summary of Contents for LED-MTX25 IP




















