ACME Elf Laser User Manual Download Page 5

 8- 

  4. How To Control The Unit   

You can operate the unit in three ways: 

 

1. By master/slave built-in preprogram function 

  2. By easy controller 

3. By universal DMX controller 

No need to turn the unit off when you change the DMX address, as new DMX address 

setting will be effected at once. Every time you turn the unit on, it will show

 

 

on the 

display and move all the motors to their ‘home’ position. After that the unit will be ready to 

receive DMX signal or run the built in programs. 

 

4.1 Master/Slave Built In Preprogrammed Function   

By linking the units in master/slave connection, the first unit will control the other units to 

give an automatic, sound activated, synchronized light show. This function is good when you 

want an instant show.   

2-light show 

In 

 (slave  mode), 

 means the unit works normally and 

 means 

2-light show. In order to create a great light show, you can set 

  on the second unit to 

get contrast movement to each other, even if you have two units only. 

 

4.2 Easy Controller   

The easy remote control is used only in master/slave mode. By connecting CA-8 to the 1/4” 

microphone jack of the first unit, you will find that the remote control on the first unit will 

control all the other units functions press the MENU button again. 

 

 

 
 
 
 

 
4.3 DMX Controller   

Use universal DMX controller to control the units, you have to set DMX address from 1 to 

512 so that the units can receive DMX signal. 

Press the 

MENU

 button up to when the 

  is showing on the display. Pressing 

ENTER

 

Stand By 

Blackout the unit 

Function 

1. Continuous line 

2.Hold for Incontinuous line 

Show 

1-4 

Pattern 

21 

Mode 

Sound (LED OFF) 

LED Blinking 

LED ON 

 9-

button and the display will blink. Use 

DOWN

 and 

UP

 button to change the DMX512 address. 

Once the address has been selected, press and keep 

ENTER

 button pressed up to when 

the display stops blinking or storing automatically 8 seconds later. To go back to the 

functions without any change press the

 MENU

 button again. Please refer to the following 

diagram to address your DMX512 channel for the first 4 units: 

 

 

 

 

4.4 DMX 512 Configuration   
 

 

Summary of Contents for Elf Laser








Reviews: