background image

MANUFACTURER’S LIMITED WARRANTY

Agri-Cover, Inc. extends the following Limited Warranty on its SNOWSPORT

TM

 Electric 

Plow Winch 
Agri-Cover, Inc. warrants its SNOWSPORT

TM

 Electric Plow Winch to be free from defects 

in material and workmanship under normal use for one (1) year from date of manufacture 

unless accompanied by proof of purchase.This limited warranty does not cover any failure 

due to abuse, misuse, alteration, neglect, improper assembly or installation, or improper 

maintenance.
Agri-Cover’s sole obligation under this warranty or any implied warranty is limited 

to the repair or replacement at its option, of defective parts only. No labor or service 

allowance is given or implied. IN NO EVENT SHALL AGRI-COVER, INC. BE 

LIABLE FOR INCIDENTAL, CONSEQUENTIAL, OR SPECIAL DAMAGES. AGRI-

COVER, INC. EXPRESSLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES OF 

MERCHANTABILITY, AND THERE ARE NO WARRANTIES WHICH EXTEND BEYOND 

THE LIMITED WARRANTY DESCRIPTION CONTAINED HEREIN.
For warranty, have serial number ready and fill out the warranty claim form at 

agricover.com/warrantyclaim or call Customer Service Department at 800-689-6612 to 

determine if only a replacement part is needed or if the product needs to be returned for 

inspection and repair. Goods to be returned must have a pre-authorized RA # (Return 

Authorization Number) – obtained by calling the number above. Mark the number on the 

package and ship it freight prepaid to address below. Agri-Cover will pay freight to return 

goods to sender. 
This Limited Warranty gives you specific legal rights and you may have other rights which 

vary from state to state.
For replacement parts shop at snowsportparts.com or call Customer Service at  

800-689-6612.

082119   2000270_

SNOWSPORT

®

 - A Division of Agri-Cover, Inc.

Hours: 8:00 am - 5:00 pm CST Monday through Friday, except Holidays

Agri-Cover, Inc.

Customer Service Dept

PO Box 508 | 3000 Hwy 281 SE

Jamestown, ND 58402

Phone: 800-689-6612

© 2019 AGRI-COVER, INC. ALL RIGHTS RESERVED.

Product subject to change without notice. Patents: agricover.com/patents. 

Summary of Contents for snowsport













Reviews: