aci PIM CPN User Manual Download Page 28

Page: 28 / 48

Photoionization Detector Module PIM CPN

User Manual

PIM_CPN - User Manual (en) - 1.08.docx

Analytical Control Instruments GmbH, Volmerstraße 9A, 12489 Berlin, Germany, www.aci-berlin.com

Page 28 of 48

10.3

Module commands

Abbreviations

Master ( microcontroller )

Slave ( this module )

10.3.1

Module information commands

Command

device ?
device [name]

Description

Get the type identification string of the module

Parameter

ident type identification string

Example

device ?

device CPN Sensor Device

Command

device.software ?
device.software [sw]

Description

Get software version of the module

Parameter

Software version string

Example

device.software ?

device.software 1.02.030

Command

device.hardware ?
device.hardware [hw]

Description

Get hardware version of the module

Parameter

Hardware version string

Example

device.hardware ?

device.hardware 1.19012.000

Command

device.username ?
device.username [name]

Description

Get or set the user name of the module

Parameter

name User name string

Maximum length 15 characters ASCII only

Example (get)

Example (set)

device.username ?

device.username My Pid

device.username Pid 001

Command

device.serialno ?
device.serialno [serial]

Description

Get the serial number of the module

Parameter

serial serial number string

Example

device.serialno ?

device.serialno A792003460

Summary of Contents for PIM CPN

















































Search results

Summary of Contents for PIM CPN

Reviews:

Related manuals for PIM CPN

Brands by name

Popular brands

aci PIM CPN, User Manual

Search results

Summary of Contents for PIM CPN

Reviews:

Related manuals for PIM CPN

Brands by name

Popular brands