background image

Automation Components, Inc.

2305 Pleasant View Road  |  Middleton, WI 53562

Phone:

 1-888-967-5224  |  

Website:

 workaci.com

Page 3

Version: 1.0

I0000467

PRODUCT SPECIFICATIONS

24 VAC or 24VDC, (+/- 10%), 50/60 Hz 
45 mA maximum 
0 to 12 VDC @ 1MΩ, 0 to 24 VDC @ 20,000Ω

0-20 mA @ 499Ω 

Fixed or Adjustable – Jumper Selectable 
Two SPDT Form “C” Relays
10A @ 120 VAC / 24VAC,  5A @ 240VAC
100,000 operations minimum
10,000,000 operations 
90° Pluggable Screw Terminal Blocks
16 (1.31 mm2) to 26 AWG (0.129 mm2)
0.5 Nm (Minimum); 0.6 Nm (Maximum)
Connect six AARs together using one connection, more if power is jumpered to 
every sixth AAR 
35 to 120°F (1.7 to 48.9°C)
10 to 95% non-condensing 
-20 to 150°F (-28.9 to 65.5°C)
Polyvinyl Chloride (PVC)
UL94 V-0 

NON-SPECIFIC INFORMATION

 

Supply Voltage:
Supply Current:
Input Voltage Signal Range (@ 
Impedance):
Input Current Signal Range (@ 
Impedance):
Deadband:
Digital Output Type:
Relay Contact Rating:
Relay Electrical Life:
Relay Mechanical Life:
Connections:
Wire Size:
Terminal Block Torque Rating:
Edge Connector:

Operating Temperature Range:
Operating Humidity Range:
Storage Temperature:
Snaptrack Material:
Snaptrack Flammability Rating:

WARRANTY

The ACI AAR Series is covered by ACI’s Two (2) Year Limited Warranty, which is located in the front of ACI’S SENSORS 
& TRANSMITTERS CATALOG or can be found on ACI’s website: www.workaci.com.

W.E.E.E. DIRECTIVE

 

At the end of their useful life the packaging and product should be disposed of via a suitable recycling 
centre. Do not dispose of with household waste. Do not burn.

Summary of Contents for AAR

Page 1: ...vice can be mounted in any position If circuit board slides out of snap track a non conductive stop may be required Use only fingers to remove board from snap track Slide out of snap track or push up against side of snap track and lift that side of the circuit board to remove Do not flex board or use tools WIRING INSTRUCTIONS PRECAUTIONS Remove power before wiring Never connect or disconnect wirin...

Page 2: ...rn on and turn off signal levels Use the Low L1 potentiometer to set the turn off level of the fixed deadband the High potentiometer is out of the circuit 2 Three input signal ranges can be selected Set J1 to the desired type Note If the first board is to receive a 0 20 mA signal then any attached boards must be set at the 0 12 VDC signal mode to operate correctly If the input signal is voltage th...

Page 3: ...6 mA Set R2 to turn OFF at 10 mA As the signal input to the AAR increases to 6 mA the load will turn ON As the signal input to the AAR continues to increase to 10 mA the load will turn OFF Problem From one analog signal I want to turn a motor ON at low speed when the signal increases to a certain value and to high speed if the signal continues to increase above the certain value Solution Set R1 to...

Page 4: ...ng 20 to 150 F 28 9 to 65 5 C Polyvinyl Chloride PVC UL94 V 0 NON SPECIFIC INFORMATION Supply Voltage Supply Current Input Voltage Signal Range Impedance Input Current Signal Range Impedance Deadband Digital Output Type Relay Contact Rating Relay Electrical Life Relay Mechanical Life Connections Wire Size Terminal Block Torque Rating Edge Connector Operating Temperature Range Operating Humidity Ra...

Reviews: