ACI Hoist & Crane MLH-005 Page 12 Operation Manual Download

Page: 12 / 16

Lever Hoists

PAGE: 12

Model MLH

MLH-005 & MLH-010

Table 7.10.1

Lubrication Schedule

PART

DESCRIPTION

FREQUENCY

Gears, bearings

Check operation of the part

Annually

Pawl pivot pin, guide

roller pin and hook

shanks

Check operation of the part

Annually

Chain wheel treads

Check operation of the part

Quarterly

Chain

Lubricate chain, under normal usage

Lubricate chain, under heavy usage require to be

lubricated more frequently

Weekly

7.10.1: Recommended Lubricants

Table 7.10.1.1

Recommended Lubricants

Part

Lubricant

Gears, bearings, pawl pivot pin, guide roller

pin, hook shanks, and chain wheel treads

Any good quality gear grease

Chain

Chain Lube

Brake parts, ratchet teeth

Do not Lubricate

The brake surfaces must be kept free of any trace

of oil or grease. Apply lubricant sparingly to the

parts near the brake to avoid oil contamination of

the brake.

Summary of Contents for MLH-005
















Search results

Summary of Contents for MLH-005

Reviews:

Related manuals for MLH-005

Brands by name

Popular brands

ACI Hoist & Crane MLH-005, Operation Manual

Search results

Summary of Contents for MLH-005

Reviews:

Related manuals for MLH-005

Brands by name

Popular brands