We have several speed sensors; the unit includes one of them or not
speed sensor in case the model has to be connected to gear box to get
speed signal.
Reed Speed Sensor and Magnet
:
4.
This sensor is universal sensor for motorcycle, find a rotatable
part to install magnet and a location can install sensor and can
be aligned to the magnet.
5.
Align the center of the magnet to either of the sensor marking
lines or the side of the sensor.
6.
Installing the sensor parallel to the vibration direction creates
optional anti-vibration effect.
7.
Make sure the gap between the magnet and the sensor is within
8mm.
Hall Effective Speed Sensor and Magnet
:
1.
This is universal sensor for ATV rear wheel installation or
motorcycle front wheel installation as if you purchase a relative
speed sensor holder.
2.
Find a part can rotate to install magnet and a location can install
sensor and the sensor can be aligned to the magnet.
3.
Align the center of the magnet to center of side face of the
sensor.
4.
Make sure the gap between the magnet and the sensor is within
5mm.
Specific Hall sensors:
The sensor such as Honda CRF, XR….etc. can replace original
sensor cable and fix it at the original position.
Thermo Sensor and Sensor Tube:
1.
The unit includes a water temperature sensor; you have to
purchase a suitable water pipe temperature sensor tube to install
the sensor easily.
2.
Cut the water pipe, insert the temperature tube into the pipe and
secure it by attached pipe clamps.
3.
Screw the sensor into the tube.
GEAR INDICATOR SETUP
The digital gear indicator calculates the ratio of speed vs engine rpm,
and displays digital gear position, there are various factors effect the
calculation, the gear indicator response slow than the actual gear
shift.
Please set wheel circumference and "SPC" of tachometer firstly, then
check if tachometer and speedometer are running stable, the setting
process can go on after connected Neutral wire and if both meters
work stable.
Start the engine at neutral gear status, try to let the wheel installed
speed sensor can rotate and the speed can be displayed on the LCD.
Leave the engine running throughout the setting procedure.
1.
Setup operations must be set up step by step. In setting screens,
each press RESET button to add the flashing digit by 1, press
MODE button to confirm the digit setting and jump to next gear
setting mode.
2.
Press and hold MODE button for 2 seconds at the digital RPM
screen to go into the total number of gears setting screen.
3.
The default number of gears is 6, the range is from 4 to 8 gears
dependent on your bike. Operation as item 1 to confirm the total
gears setting and jump to gear ratios setting screen.
4.
The gear ratios setting must be set from the 1st gear step by step
to the last gear you set. The LCD indicates and flashing "1" for
the 1st gear setting; select the bike's 1st gear and let the clutch
out, run the engine at between 2,000 and 4,000rpm and fix
speed and RPM about 5 seconds until the "-" flashing, press
MODE button to confirm 1st gear setting and jump to the 2nd
gear setting screen.
5.
The LCD indicates and flashing "2" for the 2nd gear setting;
select the 2nd gear and let the clutch out, run the engine at
between 2,000 and 4,000 rpm and fix speed and RPM about 5
seconds until the "-" flashing, press MODE button to confirm
the 2nd gear setting and jump to the 3rd gear setting screen.
6.
Go on the same process gear by gear until the last gear setting,
press MODE to confirm the last gear setting and return to main
screen mode and finish the gear indicator setting.
Please refer to the data book at
http://www.acewell-meter.com/
, find
brand, model and year of your bike to get the relative gear ratio and
input the data to the computer.
1.
Press and hold MODE button for 2 seconds at the digital RPM
screen to go into the total number of gears setting screen.
2.
In gear indicator setting screens, each press RESET button to
add the flashing digit by 1, press MODE button to confirm the
digit setting and jump to next digit or next setting screen to be
set.
3.
Setting step by step, setting the numbers of gear firstly, 1
st
, 2
nd
,
3
rd
gear...etc. Press MODE button for 2 seconds when finish the
last gear setting and go to main screen.
