BUTTON OPERATIONS
RESET BUTTON
1. Press MODE button to the desired screen then press RESET button for
2 seconds to reset TRIP 2, MAX, and MAX RPM data from stored
values to zero individually. The data of Trip 1, AVG & RT be reset
at the same time. ODO, clock and TT data cannot be reset.
MODE BUTTON
1. Press the MODE button to move all functions in loop sequence from one function screen to another when the speed sensor does not detect
any signal input.
2. Press the MODE button to move partial functions in loop from one function screen to another when speed sensor detects signal input.
SHIFT WARNING RPM OPERATION
1. Press MODE button to the RPM screen; pull on the throttle until the desired shift warning RPM displayed.
2. Press RESET button to confirm and set up the shift warning RPM.
3. Bar-graphic tachometer and a LED will flash to warning you shift gear.
4. Operate items 1 & 2 to re-adjust the shift warning RPM.
WHEEL CIRCUMFERENCE TABLE
1. The following table is calculated by the formula of Tire Diameter (inch) x 25.4(mm/inch) x 3.1416 = wheel circumference (in mm).
2. Identify the tire size of your ATV when you need to change different tire size and key in the corresponding number shown in the following chart.
UNIT & WHEEL CIRCUMFERENCE SETTING
Circumference
number (mm)
Tire Size
Tire Size
number (mm)
Circumference
Tire Size
number (mm)
Circumference
1436mm
18 inch
1357mm
17 inch
1277mm
16 inch
1197mm
15 inch
19 inch
1516mm
1756mm
1676mm
1596mm
22 inch
21 inch
20 inch
2075mm
1995mm
1915mm
1835mm
23 inch
26 inch
25 inch
24 inch
1. Setup operations include 12/24hour clock, shift warning RPM, numbers of engine rotation per signal, wheel circumference and units. You have to
set up step by step. The computer will automatic reversion to main screen if no button operation for 75 seconds at any setting screen.
2. Press both MODE & RESET buttons to go into setting screen. In setting screens, press RESET button to add the flashing digit by 1 or convert
units, press MODE button to confirm the digit setting and jump to next digit or next setting screen to be set. Press MODE button for 2 seconds at
any setting screen to finish the setting and go to main screen.
3. It displays "12 or 24H and XX:XX-XX" symbols and AM/PM in case you select 12H.
4. Press RESET button converts 12/24H, press MODE button to complete the setting and jump to clock digit setting.
5. Press RESET button to increase flashing digit by one; press MODE button to confirm digit setting and jump to next digit.
6. Press MODE button to go to shift warning RPM setting screen after set clock.
7. It displays " RPM rXXX00 ". Press RESET button to increase flashing digit by one; press MODE button to confirm digit setting and jump to next
digit.
8. Press MODE button to go to numbers of engine rotation per signal setting screen after completed shift warning RPM setting.
9. It displays "SPC-X.X RPM", the default value is 1.0; there are 4 options: 1.0, 2.0, 3.0 and 0.5. It means the numbers of engine rotation per signal.
For example the value 2.0 means the engine rotate 2 turns to output a signal.
10. Press RESET button to move in loop sequence from one to another value of the 4 values. Press MODE button to confirm the setting and go to
wheel circumference setting screen.
11. In "cXXXX" display, "c" means "Circumference", following 4 default digits; flashing digit is digit to be set.
12. Press RESET button to increase flashing digit by one; press MODE button for 2 seconds to confirm digit setting and jump to main screen.
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
RESET
2 sec
mode
reset
+
2 sec
mode
mode
mode
mode
mode
reset
mode
2sec
mode
mode
mode
mode
reset
mode
mode
mode
mode
mode
mode
