background image

 

X263W

 

 

 

INFORMATION FOR YOUR SAFETY AND COMFORT 

Safety instructions 

Read these instructions carefully. Keep this document for future reference. Follow all warnings and 
instructions marked on the product. 

CAUTION for plug as disconnecting device 

Observe the following guidelines when connecting and disconnecting power to the power supply unit: 
Install the power supply unit before connecting the power cord to the AC power outlet. 
Unplug the power cord before removing the power supply unit from the product. 
If the system has multiple sources of power, disconnect power from the system by unplugging all power 
cords from the power supplies. 

CAUTION for accessibility 

Be sure that the power outlet you plug the power cord into is easily accessible and located as close to the 
equipment operator as possible. When you need to disconnect power to the equipment, be sure to unplug 
the power cord from the electrical outlet. 

Warnings 

y

 

Do not use this product near water. 

y

 

Do not place this product on an unstable cart, stand or table. If the product falls, it could be seriously 
damaged. 

y

 

Slots and openings are provided for ventilation to ensure reliable operation of the product and to 
protect it from overheating. These openings must not be blocked or covered. The openings should 
never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product 
should never be placed near or over a radiator or heat register, or in a built-in installation unless proper 
ventilation is provided. 

y

 

Never push objects of any kind into this product through cabinet slots as they may touch dangerous 
voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind 
onto or into the product. 

y

 

To avoid damage of internal components and to prevent battery leakage, do not place the product on 
a vibrating surface. 

y

 

Never use it under sporting, exercising, or any vibrating environment which will probably cause 
unexpected short current or damage rotor devices, HDD, Optical drive, and even exposure risk from 
lithium battery pack. 

Safe listening 

Follow these instructions, suggested by hearing experts, to protect your hearing. 

y

 

Gradually increase the volume until you can hear it clearly and comfortably and without distortion. 

y

 

After setting the volume level, do not increase it after your ears adjust. 

y

 

Limit the amount of time listening to music at high volume. 

y

 

Avoid turning up the volume to block out noisy surroundings. 

y

 

Turn the volume down if you can

t hear people speaking near you. 

Summary of Contents for X263W

























Reviews: