background image

iii

,03257$176$)(7<

,16758&7,216

1.

Read these instructions carefully.  Save these instructions for
future reference.

2.

Follow all warnings and instructions marked on the product.

3.

Unplug this product from the wall outlet before cleaning.  Do not
use liquid cleaners or aerosol cleaners.  Use a damp cloth for
cleaning.

4.

Do not use this product near water.

5.

Do not place this product on an unstable cart, stand, or table.
The product may fall, causing serious damage to the product.

6.

Slots and openings in the cabinet and the back or bottom are
provided for ventilation; to ensure reliable operation of the product
and to protect it from overheating, these openings must not be
blocked or covered.  The openings should never be blocked by
placing the product on a bed, sofa, rug, or other similar surface.
This product should never be placed near or over a radiator or
heat register, or in a built-in installation unless proper ventilation is
provided.

7.

This product should be operated from the type of power indicated
on the marking label.  If you are not sure of the type of power
available, consult your dealer or local power company.

8.

This product is equipped with a 3-wire grounding-type plug, a plug
having a third (grounding) pin.  This plug will only fit into a
grounding-type power outlet.  This is a safety feature.  If you are
unable to insert the plug into the outlet, contact your electrician to
replace your obsolete outlet.  Do not defeat the purpose of the
grounding-type plug.

Summary of Contents for V60N













Reviews: