Acer P223 User Manual Download

Page: 21 / 26

EN-15

P223W

ADJUSTING THE PICTURE
The descriptions for function control LEDS

Acer eColor Management

USER

Main

icon

Sub

icon

Sub

item

Description

N/A

User mode User defined. Settings can be fine-tuned to

suit any situation

N/A

Text mode

Optimal balance of brightness and contrast

prevent eyestrain. The most comfortable way

to read onscreen text

N/A

Standard

mode

D efault Setting. Reflects native display

capability

N/A

Grahpic

mode

Enhances colors and emphasize fine detail

N/A

Movie

mode

Displays scenes in clearest detail. Pictures and
photographs appear in vibrant colors with

sharp detail)

Main

icon

Sub

icon

Sub

item

Description

Contrast

Adjust the contrast between the foreground

and background of the screen image

Brightness

Adjust the background brightness of the

screen image

ACM

ACM (Adaptive Contrast Management)A

CM ON/OFF Switch, default "OFF"

Focus

Adjust picture Focus

(available in analog mode only)

Clock

Adjust picture Clock

(available in analog mode only)

Summary of Contents for P223



























Search results

Summary of Contents for P223

Reviews:

Related manuals for P223

Brands by name

Popular brands

Acer P223, User Manual

Search results

Summary of Contents for P223

Reviews:

Related manuals for P223

Brands by name

Popular brands