Acer Business B7 Page 28 User Manual Download | Manualshive

Page: 28 / 36

background image

EN-18

Adjusting the Performance

1.

Press the MENU button to open the OSD.

2.

Using the Navi/OK button, select Performance from the OSD. Then
navigate to the setting you wish to change.

3.

Use the Navi/OK button to select the setting.

4.

Over Drive: Select Off, Normal, or Extreme.

5.

Adaptive-Sync: Select On or Off. Adaptive-Sync is available for AMD
supported graphic cards only.

6.

Refresh rate num: Display the panel’s current refresh rate on the screen.

«
...
26
27
28
29
30
...
»

Summary of Contents for Business B7





































Reviews:

No comments

Related manuals for Business B7

Brand: Safety 1st Pages: 22

Brand: Datavideo Pages: 11

Brand: Datavideo Pages: 12

Brand: Hama Pages: 51

SyncMaster 732NW

Brand: Samsung Pages: 50

SyncMaster 740B Plus

Brand: Samsung Pages: 63

SyncMaster 730MP

Brand: Samsung Pages: 72

Brand: Smart Technologies Pages: 98

5.8" TFT LCD Wide color monitor

Brand: Farenheit Pages: 4

Brand: Hartig+Helling Pages: 68

Large Matrix Galaxy GT6X Series

Brand: Daktronics Pages: 33

Brand: View Z Pages: 14

Brand: G-Lab Pages: 27

Brand: Wacom Pages: 32

Brand: NCI Pages: 4

Brand: Counterline Pages: 15

MA 275x342 20px

Brand: AESYS Pages: 45

Brand: ADCMT Pages: 306

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands