background image

v

ampere rating of the equipment plugged into the extension cord does not 
exceed the extension cord ampere rating. Also, make sure that the total 
rating of all products plugged into the wall outlet does not exceed the fuse 
rating.

Do not overload a power outlet, strip or receptacle by plugging in too 
many devices. The overall system load must not exceed 80% of the branch 
circuit rating. If power strips are used, the load should not exceed 80% of 
the power strip's input rating.

This product's power cord is equipped with a three-wire grounded plug. 
The plug only fits in a grounded power outlet. Make sure the power outlet 
is properly grounded before inserting the power cord plug. Do not insert 
the plug into a non-grounded power outlet. Contact your electrician for 
details.

Warning! The grounding pin is a safety feature. Using a power 
outlet that is not properly grounded may result in electric shock 
and/or injury.

Note: The grounding pin also provides good protection from 
unexpected noise produced by other nearby electrical devices that 
may interfere with the performance of this product.

Use the product only with the supplied power supply cord set. If you need 
to replace the power cord set, make sure that the new power cord meets 
the following requirements: detachable type, UL listed/CSA certified, type 
SPT-2, rated 7 A 125 V minimum, VDE approved or its equivalent, 4.6 
meters (15 feet) maximum length.

Product servicing

Do not attempt to service this product yourself, as opening or removing covers 
may expose you to dangerous voltage points or other risks. Refer all servicing to 
qualified service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service 
personnel when:

the power cord or plug is damaged, cut or frayed

liquid was spilled into the product

the product was exposed to rain or water

the product has been dropped or the case has been damaged

the product exhibits a distinct change in performance, indicating a need 
for service

the product does not operate normally after following the operating 
instructions

Summary of Contents for B193W - Bdmh Wide-screen LCD Monitor































Reviews: