manualshive.com logo in svg

Acer Aspire AM5610, Service Manual

Share
Download
Acer Aspire AM5610 Service Manual Download Page 27

Chapter 1

21

Hardware Monitor Function

BIOS

Note: 

The BIOS can be overwritten/upgraded by using the flash utility.

Item

Description

Feature

•  Smart fan control system, Thermal Cruise and Speed Cruise support
•  Six VID input pins for CPU Vcore identification
•  Two thermal inputs from optionally remote thermistors or 2N3904 transistors 

or Pentium 4 thermal diode output

•  Four external voltage detect inputs
•  Three intrinsic voltage monitoring (typical for Vbat, +5VSB, +5CC)
•  Two fan speed monitoring inputs
•  Two fan speed control (DC analog output)
•  WATCHDOG comparison of all monitored items
•  Overheat indication output
•  Issue SMI#, IRQ, OVT# to activate system protection

Item

Description

BIOS code 
programmer

Phoenix Award

Version

Phoenix BIOS 6.00 PC

Feature

•  ROM type: flash ROM
•  ROM size: 4MB
•  Protocol supported: PCIX 1.0, PCI 2.2, APM 1.2, VESA/DPMS (VBE/PM 

V1.1), SMBIOS 2.3, E-IDE 1.1, ACPI 1.0b, ESCD 1.03, PnP 1.0a, Bootable 
CD-ROM 1.0

•  Boot from CD-ROM feature: yes
•  LS-120 FDD drive support: yes
•  BIOS boot block feature: yes
•  Supports Microsoft SLP 2.0 for Windows Vista

Summary of Contents for Aspire AM5610


















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands