background image

 

 

Use the product only with the supplied power supply cord set. If you need to replace 

the power cord set, make sure that the new power cord meets the following 

requirements: detachable type, UL listed/CSA certified, VDE approved or its equivalent, 

4.6 meters (15 feet) maximum length. 

 

Product servicing 

Do not attempt to service this product yourself, as opening or removing covers may expose 

you to dangerous voltage points or other risks. Refer all servicing to qualified service 

personnel. 

Unplug this product from the wall outlet and refer servicing to qualified service personnel 

when: 

 

 

the power cord or plug is damaged, cut or frayed 

 

liquid was spilled into the product 

 

the product was exposed to rain or water 

 

the product has been dropped or the case has been damaged 

 

the product exhibits a distinct change in performance, indicating a need for service 

 

the product does not operate normally after following the operating instructions 

 

 

Notes

Adjust only those controls that are covered   

by the operating instructions, since improper   

adjustment of other controls may result in damage   

and will often require extensive work by a qualified   

technician to restore the product to normal condition. 

 

This server should be located in a restricted access   

location or an area with similar instruction. 

 

Caution:

 Danger of explosion if battery is   

incorrectly replaced. Replace only with the same or   

equivalent type recommended by the manufacturer.   

Dispose of used batteries according to the   

manufacturer's instructions. 

 

Disposal instructions 

 

Summary of Contents for Altos R480 F4























Reviews: