background image

 

 

Verify that the software is properly configured for the system. 

 

Refer to the software installation and operation documentation for instructions on 

setting up and using the software. Try a different version of the software to see if the 

problem is with the copy you are using. If the other version runs correctly on the 

system, contact your vendor about the defective software. 

 

No characters appear on the display monitor. 

 

Do the following: 

 

 

Is the keyboard functioning? Test it by turning the Num Lock function on and off to 

check if the Num Lock indicator lights up. 

 

Is the display monitor plugged in and turned on? If you are using a switch box, is it 

switched to the correct system? 

 

Are the brightness and contrast controls on the video monitor properly adjusted? 

 

Is the display monitor signal cable properly connected? 

 

Does this display monitor work correctly if plugged into a different system? 

 

Remove all add-in cards and see if the system boots. 

If reboot is successful, install the cards back in one at a time with a reboot between 

each addition to determine if one of them is causing the problem. 

 

Make sure that you have properly installed system-compliant memory modules, and 

that they are populated according to the system guidelines. 

 

Make sure that you have installed system compliant processors, and that they are 

populated according to the system guidelines. 

 

If you are using an add-in video controller card, do the following: 

 

1.  Verify that the display monitor works using the onboard video controller. 

2.  Verify that the add-in video controller card is fully seated in its slot. 

3.  Reboot the system for the changes to take effect. 

4.  If there are still no characters on the screen after you reboot the system, reboot it 

again. 

Take note of the beep codes emitted during POST. This information may be required if 

you seek technical assistance. 

If POST does not emit any beep code and characters still do not appear, the display 

monitor or the video controller may be defective. Contact your local Altos 

representative or authorized dealer for technical assistance. 

 

Summary of Contents for Altos BrainSphere P150 F8



















































Reviews: