background image

ii

Copyright

Copyright

©

1998-1999 Acer Netxus Inc.  All rights reserved.  No part of this

publication may be reproduced, transmitted, transcribed, stored in a

retrieval system, or translated into any language or computer language, in

any form or by any means, electronic, mechanical, magnetic, optical,

chemical, manual or otherwise, without the prior written permission of Acer

Netxus Inc.

Disclaimer

Acer Netxus Inc. makes no representations or warranties, either expressed

or implied, with respect to the contents hereof and specifically disclaims

any warranties, merchantability or fitness for any particular purpose.  Any

software described in this manual is sold or licensed “as is”.  Should the

programs prove defective following their purchase, the buyer (and not this

c o m p a n y, its distributor, or its dealer) assumes the entire cost of all

necessary servicing, repair, and any incidental or consequential damages

resulting from any defect in the software.  Furthermore, Acer Netxus Inc.

reserves the right to revise this publication and to make changes from time

to time in the contents hereof without obligation to notify any person of

such revision or changes.

Other brand and product names are trademarks and/or registered trademarks of

their respective holders

.

608-UM  1/8/99 2:34 PM  

≠∂≠

±I

Summary of Contents for ALH-608ds

































Reviews: