background image

 

1

manual should be retained for future reference. 

 

FCC Class B Radio Frequency Interference Statement  

WARNING: (FOR FCC CERTIFIED MODELS) 

 

NOTE: 

This equipment has been tested and found to comply with the limits for 

a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits 

are designed to provide reasonable protection against harmful interference in 

a residential installation. This equipment generates, uses and can radiate 

radio frequency energy, and if not installed and used in accordance with the 

instructions, may cause harmful interference to radio communications. 

However, there is no guarantee that interference will not occur in a particular 

installation. If this equipment does cause harmful interference to radio or 

television reception, which can be determined by turning the equipment off 

and on, the user is encouraged to try to correct the interference by one or 

more of the following measures: 

1. Reorient or relocate the receiving antenna. 

2. Increase the separation between the equipment and receiver. 

3. Connect the equipment into an outlet on a circuit different from that to 

which the receiver is connected. 

4. Consult the dealer or an experienced radio/TV technician for help.

 

 
 

NOTICE: 

 

1. The changes or modifications not expressly approved by the party 

responsible for compliance could void the user's authority to operate the 

equipment. 

2. Shielded interface cables and AC power cord, if any, must be used in 

order to comply with the emission limits. 

3. The manufacturer is not responsible for any radio or TV interference 

caused by unauthorized modification to this equipment. It is the  

responsibilities of the user to correct such interference.

 

 
 

WARNING:

 

 

To prevent fire or shock hazard, do not expose the monitor to rain or moisture. 

Dangerously high voltages are present inside the monitor. Do not open the 

cabinet. Refer servicing to qualified personnel only. 

 

Before operating the monitor, please read this manual thoroughly. This 

 

 
 

 

 
 

 

 

 

 

 

 
 

 

  

 

 

Summary of Contents for AL2251W





















Reviews: