Acer AL2223WD Page 5 Service Manual Download

Page: 5 / 60

- 5 -

WARNING: (FOR FCC CERTIFIED MODELS)

NOTE:

this equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy,

and if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception,

Which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4. Consult the dealer or an experienced radio/TV technician for help.

NOTICE:

1. The changes or modifications not expressly approved by the party responsible for compliance could void

the user ’s authority to operate the equipment.

2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.

3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to

this equipment. It is the responsibility of the user to correct such interference.

As an ENERGY STAR

Partner our company has determined that this product meets the ENERGY STAR

guidelines for energy efficiency.

WARNING:

To prevent fire or chock hazard, do not expose the monitor to rain or moisture. Dangerously high voltages are

present inside the monitor. Do not open the cabinet. Refer servicing to qualified personnel only.

Summary of Contents for AL2223WD





























































Search results

Summary of Contents for AL2223WD

Reviews:

Related manuals for AL2223WD

Brands by name

Popular brands

Acer AL2223WD, Service Manual

Search results

Summary of Contents for AL2223WD

Reviews:

Related manuals for AL2223WD

Brands by name

Popular brands