Acer al200 User Manual Download Page 17

Page: 17 / 19

AL2002W

E-15

SPECIFICATION

LCD Display

Display Type

20" TFT LCD

Display Area (W x H)

433.4 x 270.9 mm

Contrast Ratio

800:1 (Typ.)

Viewing Angle

160

H 160

V (CR=10)

Power Input

Voltage

100-240Vac

Frequency

50-60Hz

Current Rating

1.5A

Operational Features

Display Colors

16.7M

Resolution

WSXGA (1680 x 1050) at 60 Hz maximum.

Brightness

300 cd/m

(Typ.)

Response Time

5 ms (Typ.)

Interface

Analog RGB, Digital(Only Dual-Input Model)

Input Connector

15-pin D-sub, DVI-D Cable(Only Dual-Input Model)

Users Controls

Front Panel Controls

Power On/Off, MENU, Select DOWN( ),Select

DOWN( ) to switch Analog and Digital Value(+/-
)(Only Dual-Input Model), +/AUTO,-.

OSD Controls
(Note)

Brightness, Contrast, Auto Contrast, Color
Temperature, Horizontal Size, Fine, Left/Right,

Down/Up, Auto-Adjust, Language, Factory Reset,

OSD Time Out, OSD Left/Right, OSD Down/Up,

Information

Note : for DVI mode, Auto Contrast, Horizontal

size,Fine, Left/Right, Down/Up, Auto Adjust will

bedisabled.

Summary of Contents for al200




















Search results

Summary of Contents for al200

Reviews:

Related manuals for al200

Brands by name

Popular brands

Acer al200, User Manual

Search results

Summary of Contents for al200

Reviews:

Related manuals for al200

Brands by name

Popular brands