ACE R/C 1400 Glider Operation Manual Download Page 1

Ace R/C Whisper 1400 Glider R/C Sailplane (4104-F)

Distributed by Ace Hobby Distributors, Inc. • 116 W 19th ST, Higginsville, MO  64037

Phone: 660-584-7121 • www.acehobby.com • E-mail: [email protected]

Whisper 1400 Glider

Operation Manual

Specifications:

Wingspan: 

55”(1400mm)

Length:  

32.5”(825mm)

Wing area: 

323 sq. in.

Weight:  

16 oz.(453g)

Warranty

       This kit is guaranteed to be free from defects in material and workmanship at the date of purchase.  It does not 

cover any damage caused by use or modification.  The warranty does not extend beyond the product itself and is limited 

only to the original cost of the kit.
     By the act of building this user-assembled kit, the user accepts all resulting lliability for damage caused by the 

final product.  If the buyer is not prepared to accept this liability, it can be returned new and unused to the place 

of purchase for a refund.

Notice:  Adult Supervision Required

    This is not a toy.  Assembly and flying of this product requires adult supervision. 
    Read through this book completely and become familiar with the assembly and flight of this airplane.  Inspect all 

parts for completeness and damage.  If you encounter any problems, call 660-584-6724 for help.

JE6103

Summary of Contents for 1400 Glider













Reviews: