background image

 

23 

 

 

MAINTENANCE 

 

In order to ensure optimal availability of the unit, a number of checks and inspections on the unit and 
the field wiring have to be carried out at regular intervals.   
 

BEFORE CARRYING OUT ANY MAINTENANCE OR REPAIR ACTIVITY, ALWAYS SWITCH ‘OFF’ THE 
CIRCUIT BREAKER ON THE SUPPLY PANEL, REMOVE THE FUSES OR OPEN THE PROTECTION 

DEVICES OF THE UNIT. 

MAKE SURE THAT BEFORE STARTING ANY MAINTENANCE OR REPAIR ACTIVITIES THE POWER 
SUPPLY TO THE OUTDOOR UNIT IS SWITCHED ‘OFF’. 

 
The described checks must be executed at least once a year. 
1.

 

Water pressure 

    Check if the water pressure is above 0.3 bar. If necessary add water. 

2.

 

Domestic hot water tank pressure relief valve (field supply)   

Applies only to installations with a domestic hot water tank. 
Check for a correct operation of the pressure relief valve on the domestic hot water tank. 

3.

 

Domestic hot water tank booster heater(field supply) 

Applies only to installations with a domestic hot water tank.   
It is advisable to remove lime build up on the booster heater to extend its life span, especially in 
regions with hard water. To do so, drain the domestic hot water tank, remove the booster heater 
from the domestic hot water tank and immerse in a bucket (or similar) with lime-removing product 
for 24 hours. 

 

 
 

Summary of Contents for SDAW4.6-220






























Reviews: