Accutone V10 Install Manual & User Manual Download Page 10

Page: 10 / 10

SOFTWARE TROUBLESHOOTING

“Start” > “All Programs” > “USB Speakerphone” > “Uninstall USB” >

“SpeakerPhone”

GENERAL TIPS

- If you don’t see “Auto Enable AEC with Skype” when you right click on the program icon in the

system tray, it may means that you V10 is not connected, or it wasn’t connected during installation.
Keep V10 plugged in, go to

. When the uninstaller starts up, choose Repair and the software will reinstall, and

system restart. After restarts, you should be able to see the selection when you right click the icon.

- Make sure you turn off “Let Skype adjust my audio settings” in the skype program’s audio setting as

shown in section B6 of this manual.

- Skype, by default, will use the “Windows default device” as it’s audio in and audio out settings. V10

will change Windows’ default audio input and output device to “V10 Audio Device” or “ USB VoIP
Device” automatically, once it is plugged in. But, if there’s no sound coming from V10, you can
manually change the device by going into “Control Panel” > “Sounds and Audio Devices” >
“Audio” > “Sound Playback” & “Sound Recording” to change the device to “V10 Audio Device” or
“USB VoIP Device”.

- You can also just select your audio device from within Skype by “Tools” from the top menu of

Skype, > “Options” > “Audio Settings” > “Microphone” or “Speakers” and select “V10 Audio
Device” or “USB VoIP Device”.

- For better acoustic performance, always flip the black door and let V10 stand upright.
- Plug in the 3.5mm headphone for private communication and have the best fully duplex sound

quality.

- Master Volume can be adjusted from Windows “Sound and Audio Devices” setting, aside from the

V10 main interface.

- For addition information of V10 or software update, please visit our official website at

http://www.accutone.com.

Appendix

Standards, Terms & Conditions.

D1. general tips and reminders

Appendix

[ inspiring people, inspiring change ]

V10 - Installation Guide & User Manual

D3. CE/EMC Declaration

This  V10  has  been  marked  with  the  CE  mark.  This  mark  indicates  compliance  with  EEC
directives  89/336/EEC/EN55024/EN5022.The  validity  of  the  CE  marking  is  restricted  to
only  those  countries  when  it  is  legally  enforced,  mainly  in  the  countries  of  the  European
Economic Area.

D5. trademark and ownership

Accutone and the logo design combined are trademarks or registered trademarks of Accutone

Technologies Limited.

Microsoft and Windows are registered trademarks or trademarks of Microsoft Corporation in the

United States and/or other countries.

Pentium is a trademark or registered trademark of Intel Corporation.

Skype is a trademark or registered trademark of Skype Technologies S.A.

Apple Computer Inc. has intellectual property rights over "Apple", "Macintosh" and "OSX".

In this manual, Microsoft Windows XP Home Edition and Microsoft Windows XP Professional

Edition are referred to as Windows XP, whereas Microsoft 2000 Professional Edition is referred

to as Windows 2000, Microsoft Millennium Edition is referred to as Windows Me, and Microsoft

Windows 98 Second Edition is referred to as Windows 98 SE.

D4. FCC Requirements - Part 15 Class B device or Peripheral

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection  against  harmful  interference  in  a  residential  installation.  This  equipment  generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions,  may  cause  harmful  interference  to  radio  communications.  However,  there  is  no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful  interference  to  radio  or  television  reception,  which  can  be  determined  by  turning  the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.

general tips and reminders

precautions on safety

CE/EMC & FCC

trademark and ownership

- Listening with the headset at high volume may damage your hearing.
- Adjusting the volume for microphone or speaker too high may cause squealing (feedback sound)

and can damage your hearing.

- Do not use while driving.
- Place product far away from water, fire, extended exposure of direct sunlight or magnetic field,

and places of excessive dust, moist, rain, shock or electromagnetic radiation.

- Do not drop your device or subject it to external shock which may cause malfunction.
- Do not disassemble or attempt to open up the casing of the conference phone.
- Whenever unplugging the USB plug, apply force to the plug part only. Jerking the cord instead of

the plug may cause damage to the product.

- Do not use any liquid substance to clean the casing of the product.

D2. precautions on safety