background image

 

4

 

 

 

WARNING 

 DANGER TO LIFE!  High voltage in the inside of the 

unit. Never operate the unit with removed top cover and do never 
touch the board while the unit is switched on! 

 
 

 

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user 

to presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of 

sufficient magnitude to constitute a risk of electric shock to persons. 

 

The exclamation point within an equilateral triangle is intended to alert the user to the presence of 
important operation and maintenance (servicing) instructions in the literature accompanying the 
appliance. 

 

Marking by the “CE” symbol indicates compliance of this device with the EMC (

Electromagnetic 

Compatibility) and LVD (Low Voltage Directive) standards of the European Community. 

 
Remarks in the manual: 

 

WARNING! 

 

Calls attention to a procedure, practice, condition or the like that, if not correctly 
performed or adhered to, could result in personal injury or death. 
 

CAUTION!

 

Calls attention to a procedure, practice, condition or the like that, if not correctly 
performed or adhered to, could result in a damage or destruction to part or the entire 
component. 

 

 

To guarantee a reliable function of this unit over the long-term we kindly ask you to thoroughly 

read this 

instruction manual

 before connecting this unit and to observe the following instructions. This is also necessary for 

your own safety when dealing with the unit. 

 

 

 

VERY 

IMPORTANT! 

 

 
Never

 

leave the appliance unsupervised when in use. Always keep electrical 

equipment out of the reach of children.  

 
 

 

VERY 

IMPORTANT! 

 

 
After switching the unit off please wait 60 seconds before switching it on again. 
 

 
 

 

VERY 

IMPORTANT! 

 

 
Never use the unit in a room with temperature more than 25 °C and high humidity. 
Never use the unit outside. 

 
 
 

3  Introduction and positioning 

 
The MONO III - MK 2 is a powerful power amplifier. Please read through all important information provided by this 
instruction manual for the handling and operation of this top-quality high-end product. 
 
The weight of this MONO III 

 MK 2 is approx. 60 kg / 132 lbs. Great care must be exercised when unpacking the 

unit. Due its high weight a minimum of two people should unpack the amplifier out of its box.  
 

Summary of Contents for MONO II-MK2














Reviews: