background image

3. Safety Instructions 

Please read and understand all of the following instructions, prior 
to using this tool. Failure to do so, may result in bodily injury.

©2008 Johnson Level & Tool

3

DANGER!

Class IIIa Laser Product

Max. Power Output:

5mW

Wavelength: 625-645nm

THIS TOOL EMITS LASER RADIATION.

DO NOT STARE INTO BEAM.

AVOID DIRECT EYE EXPOSURE.

ATTENTION

IMPORTANT

• Read all instructions prior to operating this laser tool. Do not remove any labels from tool.

• Use of controls or performance of procedures other than those specified herein may void warranty.

• Do not stare directly at the laser beam.

• Do not project the laser beam directly into the eyes of others.

• Do not set up laser tool at eye level or operate the tool near a reflective surface as the

laser beam could be projected into your eyes or into the eyes of others.

• Do not place the laser tool in a manner that may cause someone to unintentionally look

into the laser beam. Serious eye injury may result.

• Do not operate the tool in explosive environments, i.e. in the presence of gases or flamma-

ble liquids.

• Keep the laser tool out of the reach of children and other untrained persons.

• Do not attempt to view the laser beam through optical tools such as telescopes as serious

eye injury may result.

• Always turn the laser tool off when not in use or left unattended for a period of time.

• Remove the batteries when storing the tool for an extended time (more than 3 months) to

avoid damage to the tool should the batteries deteriorate.

• Do not attempt to repair or disassemble the laser tool. If unqualified persons attempt to

repair this tool, it may void the warranty.

• Use only original AccuLine Pro

®

parts and accessories purchased from your AccuLine Pro

authorized dealer. Use of non-AccuLine Pro parts and accessories will void warranty.

1676H-English  10/3/08  10:46 AM  Page 3

Summary of Contents for 40-6602



















Reviews: