M 0495
-
8
GB
7 - FUNCTION AND PRECISION CHECK
If faults or inaccuracies are encountered which are not readily identified, it may be useful to perform the function and
precision check.
PRELIMINARY CONTROLS
·
Carefully clean the flange and cones
·
Spring cover sliding
·
Shaft terminal locking
ENCODER CHECK (see
SELF-DIAGNOSTICS
)
·
POS =
outside display: 0-127 turning the shaft by hand
LED matrix:
Clockwise,
anticlockwise
TEST OF PROPER ENCODER FUNCTIONING
1. Cleaning the encoder
Remove the snap cover on the chuck side.
Insert a tool until it touches the phase disc (use a soft brush to prevent damaging the decals).
Slowly turn the wheel by hand several times to allow the tool to remove any residual dust.
Never force the tool on the phase generator.
After cleaning, close the snap cover.
2. Positioning the encoder card
It is recommended to position the encoder card in the following cases:
- If replacing the encoder card;
- If replacing, cleaning or generally working on the encoder decals;
- In the event of repeated errors 1,2,11,12,13,14,15,16,17,18 detected by the wheel balancer during the unbalance
measurement phase;
- In the event of unjustified unbalance oscillation.
Before running the encoder test, ALWAYS check that there is a maximum distance of 1 mm between the decal and
the encoder card and that the retaining nuts of the encoder card are adequately tightened.
Use a wheel of average dimensions.
Press:
[MENU]
[
]
The word [Setup] appears
[ENTER]
The word [Diagn.] appears
[MENU]+[STOP]+[MENU]
Press in sequence in maximum 5 sec.
[
]
The word [Enc.] appears
[ENTER]
The word [Start] appears
[START]
The test cycle is run after which the following results must be obtained for
the encoder to function properly:
[ 32] [ 32]
Number of encoder pulses A/B
[Min.] [0.15]
The number displayed must be in a range of 0.12%0.25.
[xxx]
[xxx]
The number shown on the left-hand display must be higher by as much
as possible than the right-hand number and both values must be as far
as possible away from 0.
MEANING OF ENCODER TEST ERRORS
Err. 1
No reset signal.
1. Check the connection cable between the encoder card and
the CPU board.
2. Check positioning of the encoder card.
3. Clean the encoder decal.
4. Replace the encoder card
5. Replace the CPU board
Err. 2
Encoder test speed not reached.
1. Check positioning of the encoder card.
2. Clean the encoder decal.
3. Replace the encoder card
4. Replace the CPU board
Err. 4
Incorrect direction of rotation.
1. Check the encoder card connection cable.
Err. 33
Rising edge fault detected for ENCA. 1. Check positioning of the encoder card.
2. Clean the encoder decal.
Summary of Contents for 1250
