Acces USB-DIO-24 User Manual Download Page 3

Manual USB-DIO24-CTR6 

Warranty

 

 

Prior to shipment, ACCES equipment is thoroughly inspected and tested to applicable 
specifications. However, should equipment failure occur, ACCES assures its customers that prompt 
service and support will be available. All equipment originally manufactured by ACCES which is 
found to be defective will be repaired or replaced subject to the following considerations. 

 

Terms and Conditions

 

If a unit is suspected of failure, contact ACCES' Customer Service department. Be prepared to give 
the unit model number, serial number, and a description of the failure symptom(s). We may suggest 
some simple tests to confirm the failure. We will assign a Return Material Authorization (RMA) 
number which must appear on the outer label of the return package. All units/components should 
be properly packed for handling and returned with freight prepaid to the ACCES designated Service 
Center, and will be returned to the customer's/user's site freight prepaid and invoiced. 

 

Coverage

 

First Three Years: Returned unit/part will be repaired and/or replaced at ACCES option with no 
charge for labor or parts not excluded by warranty. Warranty commences with equipment shipment. 
  
Following Years: Throughout your equipment's lifetime, ACCES stands ready to provide on-site or 
in-plant service at reasonable rates similar to those of other manufacturers in the industry. 

 

Equipment Not Manufactured by ACCES

 

Equipment provided but not manufactured by ACCES is warranted and will be repaired according to 
the terms and conditions of the respective equipment manufacturer's warranty. 

 

General

 

Under this Warranty, liability of ACCES is limited to replacing, repairing or issuing credit (at ACCES 
discretion) for any products which are proved to be defective during the warranty period. In no case 
is ACCES liable for consequential or special damage arriving from use or misuse of our product. 
The customer is responsible for all charges caused by modifications or additions to ACCES 
equipment not approved in writing by ACCES or, if in ACCES opinion the equipment has been 
subjected to abnormal use. "Abnormal use" for purposes of this warranty is defined as any use to 
which the equipment is exposed other than that use specified or intended as evidenced by 
purchase or sales representation. Other than the above, no other warranty, expressed or implied, 
shall apply to any and all such equipment furnished or sold by ACCES.

 

 
 

 

 

Summary of Contents for USB-DIO-24





















Reviews: