background image

PCIe-COM-4SMDB and RJ Family Manual 

10

Hardware Installation 

 
 

Caution! * ESD

 

A single static discharge can damage your card and cause 
premature failure! Please follow all reasonable precautions to 
prevent a static discharge such as grounding yourself by touching 
any grounded surface 

prior to touching the card.

 

 

1.  Do not install the card into the computer until the software has been fully installed. 
2.  Turn OFF computer power AND unplug AC power from the system. 
3.  Remove the computer cover. 
4.  Carefully install the card in an available PCIe expansion slot (you may need to remove a 

backplate first). 

5.  Inspect for proper fit of the card and install and tighten the mounting bracket screw. Make 

sure that the card mounting bracket is properly screwed into place and that there is a 
positive chassis ground. 

6.  Four-port “DB” model cards use a header to DB9M cable accessory that installs in an 

adjacent mounting bracket / slot location.  Install this and tighten screw. 

 

 

 

Figure 2-1: Port Configuration Utility Screenshot 

7.  Replace the computer cover and turn ON the computer.  
8.  Most computers should auto-detect the card (depending on the operating system) and 

automatically finish installing the drivers. 

9.  Run the Port Configuration Utility program (setup.exe) to configure the protocol (RS-

232/422/485) for each COM port. 

10. Run one of the provided sample programs that was copied to the newly created card 

directory (from the CD) to test and validate your installation. 

 

Summary of Contents for PCIe-COM-2SDB





















Reviews: