READ ME FIRST – SETUP INSTRUCTIONS
Thank you for purchasing the Accell UltraAV HDMI Distribution
Amplifi
er. This product is designed to provide an exceptional
performance and value. Please review the manual before
operating and retain for future reference.
- CAUTION -
1. Ensure the unit has suf
fi
cient
ventilation. Do not cover
ventilation openings. Do not install
in a confi
ned space.
2. Do not operate near source
of heat. Do not stack on top,
underneath or between other heat
generating unit/s including other
amplifi
ers.
3. Unplug power adapter if not
used for an extended period.
4. To prevent damage from power
surges, the unit should be plugged
into a surge protector or surge pro-
tected power source.
5. Do not use near liquid or areas
of heavy moisture.
6. Clean unit with a clean and dry
cloth only.
7. This unit cannot be serviced in
the
fi
eld. Contact Accell if service is
required.
8. Do not open case, risk of shock -
shock hazard.
9. Do not modify power cord or use
the product if the power cord is
damaged.
Introduction
The UltraAV 4x4 HDMI Matrix and Distribution Amplifier accepts signals
from up to 4 HDMI enabled audio/video sources and distributes the
signal to up to 4 HDMI enabled displays. The matrix can be configured to
send any input to any HDMI displays, monitors, projectors or TV’s.
Over-Current and Over-Voltage Protection
The circuit boards are equipped with both over-current and over-voltage
protection and will automatically power down if encountered. The circuit
boards will restore automatically once the excessive current or voltage
has passed.
Package Contents
●HDMI Distribution Amplifier (Matrix)
●
Power Adapter
●Remote Control (with battery)
●
Owner’s Manual
●CD-ROM (for RS-232 control)
Model Number:
K072C-013B
UltraAV
®
HDMI 4x4 Matrix and
Distribution Amplifier
Setup
With the matrix power switch in the OFF position, connect an HDMI High
Speed cable from the HDMI Output of the most commonly used audio/
video source to the HDMI Input 1 located on the rear of the matrix.
Similarly
, connect the remaining source devices to the HDMI Input Ports
on the matrix.
Tips: Use the shortest length HDMI cables possible in each point
in the installation. Use only High Quality and High Speed HDMI
cables.
Next, connect an HDMI cable to the HDMI Output Port 1 on the rear of
the matrix. Connect the other end to the HDMI Input Port of the display
device. Similarly
, connect the remaining HDMI Output Ports from the
matrix to the other displays.
The matrix has internal memory that stores the system
information for faster switching. Please follow the steps in the
order listed:
T
urn ON the displays and ensure they are awake (not in
standby mode). Check the displa
ys INPUT setting to ensure the correct
HDMI port is active.
T
urn on the source devices and ensure they are awake (not in standby
mode). Connect the power adapter to the matrix. Plug the power
adapter into a surge protected AC power outlet. Turn the matrix power
switch to the ON position.
The matrix has a low power draw and is intended to be left on. If
the matrix is turned off, start up the system as noted above. If new
hardw
are is added, please perform a RESET
.
To
RESET the matrix, turn off the display and source devices.
Power off
the matrix and unplug the power adapter from the rear of the matrix.
Wait 20 minutes for the memory of the system configuration inside of
the matrix to be deleted. Follow the setup instructions above to correctly
initiate the setup.
HDMI 4x4 Matrix and Distribution Amplifier
Model: K072C-013B
Speci
fi
cations
● Independently access 4 HDMI Sources from 4 HDMI
Displays
● Supports HD resolutions up to 1080P and 3D
● HDMI 1.4a, HDCP 1.2 compliant
● Input video signal: 5v p-p, Input DDC signal: 5v p-p (TTL)
● Data transfer speed of 6.75Gbps (2.25Gbps/channel)
● Audio formats supported:
DT
S-HD 7.1, Dolby T
rue-HD 7.1
● Deep color up to 36-bi
t
● RS232 P
ort for control
● Maximum input cable length: Up to 20m (24AWG)
● Maximum output cable length: Up to 20m (24AWG)
● Shelf or surface mountabl
e
● 5V DC, UL Listed power adapter
● Approximate dimensions: 10.9”W x 1.1”H x 6.1”D
277W x 28H x 156D mm
● Oper
ating temperature r
ange: 5 to 131°F (-15 to 55°C)
● Oper
ating humidity r
ange: 5% to 90% RH (no condensation)
LED indicator lights
On initial power on, all LED lights on the matrix should come on solid
blue. All the numerical LED displays will momentarily read ‘0’ and
then change to ‘1’. If less than the maximum number of Displays
are connected to the matrix (not all the outputs are used) the
numerical indicator will indicate ‘0’ for that output and there will be no
corresponding
HDMI OUT
blue LED for the unused output. Blue lights
will only appear for devices connected. Any unused HDMI Input ports will
also have its
HDMI IN
blue LED unlit.
Operation
Manual Control:
You can operate HDMI source switching manually by
using the buttons labeled ‘Out” located on the front panel. Press the
button that corresponds to the output that you want to change the HDMI
source on and toggle through until the desired HDMI input source video
is being displayed. A numerical LED indicates which HDMI source input is
being shown on each output (HDTV).
Remote Control:
Included with the Matrix is a R
emote Control. The
remote control can control the matrix by pointing it at the front of the
matrix, targeting the integr
ated IR receiv
er labeled
IR
. IR uses line-of
-
sight between the remote control (or IR
-T
X) and the receiver
. The angle
which the remote will work is at about a 15° degree angle in either
direction to the receiver. If the receiver is postioned such that there
is not line-of
-sight, the port labeled “IR Extender” accepts an optional
IR R
eceiver. This receiver enables line-of-sight if the matrix is out of
position.
LED Indicator Lights
