AC Infinity CONTROLLER 76 User Manual Download Page 25

Page: 25 / 26

No part of the materials including graphics or logos available in this booklet may be copied, photocopied, reproduced,
translated or reduced to any electronic medium or machine readable form, in whole or in part, without specific
permission from AC Infinity Inc.

FCC Warning

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this

device may not cause harmful interference, and (2) this device must accept any inte rference received, including

interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's

authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interferenceto radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

Summary of Contents for CONTROLLER 76



























Search results

Summary of Contents for CONTROLLER 76

Reviews:

Related manuals for CONTROLLER 76

Brands by name

Popular brands

AC Infinity CONTROLLER 76, User Manual

Search results

Summary of Contents for CONTROLLER 76

Reviews:

Related manuals for CONTROLLER 76

Brands by name

Popular brands