Example:
Projector Command format:
POWER ON
=> 02H 00H 00H 00H 00H 02H
POWER OFF
=> 02H 01H 00H 00H 00H 03H
Video Source
=> 02H 03H 00H 00H 02H 01H 01H 09H 31H 12H 5FH AAH
RGB Source
=> 02H 03H 00H 00H 02H 01H 01H 09H 31H 12H 5FH
Coding set are as followed:
(1). POWER ON
Transmitted code
: 53 45 54 52 06 50 57 4E 02 00 00 00 00 02
Confirm Return code : 52 54 55 4E 06 50 57 4E 02 00 00 00 00 02
(2). POWER OFF
Transmitted code
: 53 45 54 52 06 50 57 46 02 01 00 00 00 03
Confirm Return code : 52 54 55 4E 06 50 57 46 02 01 00 00 00 03
(3). Input Source - 1
Transmitted code
: 53 45 54 52 0C 56 44 31 02 03 00 00 02 01 01 09 31 12 5F AA
Confirm Return code : 52 54 55 4E 0C 56 44 31 02 03 00 00 02 01 01 09 31 12 5F AA
(4). Input Source - 2
Transmitted code
: 53 45 54 52 0B 50 43 31 02 03 00 00 02 01 01 09 31 13 5F
Confirm Return code : 52 54 55 4E 0B 50 43 31 02 03 00 00 02 01 01 09 31 13 5F
RS-232 PROGRAMMING
ABtUS
AVS-SSR8/2
2. Setting the Projector Communication parameter :
Header code
(4 byte) +
Data code length
(1 byte) +
Command ID
(3 byte) +
Data code
(2 byte).
Header code
: 53H 45H 54H 52H
Data code length
: 02H
Command ID
: 42H 41H 55H
Data code
: XXH YYH
XXH => Projector Baud rate and reference are as followed :
(1). 00H : 1200bps.
(2). 01H : 2400bps.
(3). 02H : 4800bps.
(4). 03H : 9600bps.
YYH =>Projector Data Length and Parity bit and reference are as followed :
(1). 00H : Data length 8bits, No Parity.
(2). 01H : Data length 8bits, Odd Parity.
(3). 02H : Data length 8bits, Even Parity.
(5). 04H : 19200bps.
(6). 05H : 38400bps.
(7). 06H : 115200bps.
to be continued..
OPERATION:
1) Setting the unit to
IR Leaning mode
:
Press and hold
UP
and
DOWN
button at the same time for 3 sec.
both
UP
and
DOWN
button LED will be blinking.
IR Learn Mode
is then activated.
1.1) Learning Projector Power OFF
In
IR Learn Mode
, press the
UP
button. The
UP
button LED will be blinking.
Point the Projector remote at about 1-2cm away from the
IR window
, press and
hold the
Power
button till the STOP LED is
ON
.
IR learning completed.
1.2) Learning Projector Power ON
In
IR Learn Mode
, press the
DOWN
button. The
DOWN
button LED will be blinking.
Point the Projector remote at about 1-2cm away from the
IR window
, press and
hold the
Power
button again till the STOP LED is
ON
.
IR learning completed.
1.3) Learning Projector PC source select
In
IR Learn Mode
, press the
UP
and
STOP
button at the same time.
The
UP
button LED will be blinking while the
STOP
button LED stays ON.
Point the Projector remote at about 1-2cm away from the
IR window
, press and
hold the
VGA Input
button till the STOP LED is
ON
.
IR learning completed.
1.4) Learning Projector Video source select
In IR Learn Mode, press the
DOWN
and
STOP
button at the same time.
The
DOWN
button LED will be blinking while the
STOP
button LED stays ON.
Point the Projector remote at about 1-2cm away from the
IR window
, press and
hold the
Video Input
button till the STOP LED is
ON
.
IR learning completed.
LEARING OF PROJECTOR IR CODE
Installation Guide
Important Note:
After termination, if motor does not move, please reset
by switching on and off the incoming power supply.
ABtUS
AVS-SSR8/2
06
03
