ABSCO SHEDS MB60303HK Manual Download Page 38

Page: 38 / 44

ABSCO HIGHLANDER SHED

MODEL: 60303HK

5.96mW x 3.00mD x 2.30mH

Model: 60303HK

29/11/2021

1.4

Absco Industries

Assembly Instruction Manual

FINAL CONSTRUCTION

ANCHORING OF SHED

Each anchor consists of one nut, bolt, M10
dynabolt and steel angle.
Drill a 10mm hole into the wall sheet.
Drill a 10mm hole into the concrete.

Bolt and Nut*
M10 4.6/S

Steel Angle*
45 x 45 x 3EA
34LONG G450
2x 130 Ø Holes

M10 Dynabolt*

* Denotes hot dip galvanised fi nish

Wall Sheet

Slab

STEP 1.
Secure the roof panels to the wall panels
as shown.

STEP 2.
Secure the roof panels to the internal
frames with self drilling tek screws.

STEP 3.
Secure the portal frames to the ridge
beam as detailed on the previous page.

STEP 4.
Bend the top and bottom flanges as
shown, then hook the bottom flanges
under the top channel and screw top to
the ridge beam with two screws.

Location of 24 concrete anchors.
Refer to section PORTAL FRAME for
portal anchor locations.

Summary of Contents for MB60303HK













































Search results

Summary of Contents for MB60303HK

Reviews:

Related manuals for MB60303HK

Brands by name

Popular brands

ABSCO SHEDS MB60303HK, Manual

Search results

Summary of Contents for MB60303HK

Reviews:

Related manuals for MB60303HK

Brands by name

Popular brands