ABSCO SHEDS CYCRK Assembly & Instruction Manual Download

Page: 1 / 25

Absco Industries

Assembly Instruction Manual

GABLE SHED

N3/C1 FRAME KIT

FOR REGENT MODELS

Model: CYCRK

02/02/21

1.2

DOWNLOAD

OUR APP FOR

ASSEMBLY

VIDEOS

LEAVE A REVIEW

Tell us about your experience and

receive a $20 Coles Gift Card.

Visit

www.abscosheds.com.au/review

AU: 1800 029 701

NZ: 0800 466 444

[email protected]

www.abscosheds.com.au

This kit is applicable to the following sheds:

The addition of this frame kit will increase the
wind rating of the specified sheds to

Wind rating: N3/C1 as per AS4055-2012.
Suitable for specific cyclonic regions

30372RK
30292RK
30222RK

30142RK
23221RK
23141RK

WARNING: This shed must be anchored to a
100mm thick concrete slab with the concrete
anchors supplied.
Failure to do so will result in the shed not
having the structural integrity required to
endure a severe storms or cyclonic event.

WARNING: Doors must remain closed with
all padbolts properly secured during severe
storms or cyclonic event.

Where information conflicts with the original
instruction manual, this document is to be
referenced.

View of frame kit applied to

30372RK

This instruction manual is to be used during
the initial construction of the structure.

Summary of Contents for CYCRK


























Search results

Summary of Contents for CYCRK

Reviews:

Related manuals for CYCRK

Brands by name

Popular brands

ABSCO SHEDS CYCRK, Assembly & Instruction Manual

Search results

Summary of Contents for CYCRK

Reviews:

Related manuals for CYCRK

Brands by name

Popular brands