background image

- 5 -

CONTROLLER FUNCTION

PTT

MIC

Before any operation, apply positive voltage to the IGN (Ignition) 

wire at the rear to power-up the unit.

PTT: 

Activate  Microphone  for  PA  Broadcast  through  the  siren 

speaker. This Button overrides all other acoustic function (i.e. Air 

Horn, Siren Tone and Radio Rebroadcast) while it is activated.

Code 1, 2, 3: 

Each Code button (

Code 1

Code 2

Code 3

) may 

be  programmed  to  turn  on  and  off  switch  button  controls 

(

SW1

~

SW4

) and/or 

SIREN

 button together. These buttons may 

still be operated independently. (See "PROGRAMMING" section 

for more details) By default, 

Code 1~3

 will operate with 

SW1~3

 

respectively with an additional 

SIREN

 on 

Code 3

.

MAN: 

When the Siren Tone is not activated, this button gener-

ates Manual WAIL Tone that will ramp up to sustain a specific 

pitch until released (stopped immediately). When 

the Siren Tone is activated, press this button to cycle through all 

the tones in the tone cycle. (For available Siren Tone Cycles, see 

“PROGRAMMING” section for more details)

HORN: 

Momentarily  activate  the  Air  Horn  Tone  when  it  is 

pressed. This tone will override all other Siren Tones and Radio 

Rebroadcast  while  it  is  activated.  This  function  can  also  be 

activated through the HRT input wire at the rear.

SIREN: 

Activate Siren Tone. (To set Siren Tone, See “PROG- 

RAMMING” section for more details) This Button will de-activate 

the Radio Rebroadcast upon activation. It may be interlocked by 

SW1

.  (See  “Siren  Interlock  /  Horn  Disable  Setting”  section  for 

more details)

RADIO: 

Activate Radio Rebroadcast through the siren speaker. 

This button will de-activate the Siren Tone upon activation.

SW1: 

Activate  SW1  Output;  It  may  be  used  for  the  primary 

warning light and interlocking 

SIREN

SW2

SW3

 and/or 

SW4

(See  “Siren  Interlock  /  Horn  Disable  Setting”  section  for  more 

details)

SW2:

 Activate SW2 Output. 

SW3: 

Activate SW3 Output.

SW4: 

Activate SW4 Output.

NOTE: SW1

~

SW4

 buttons can be programmed for three operat-

ing  modes  such  as  ON/OFF,  Momentary  or  Timer  (10 

seconds)  Switch.  (See  “PROGRAMMING”  section  for 

more details)

NOTE: 

The controller is shipped without any 

button decals installed. Place the proper decal 

onto each button.

Button Decal

Tone Cycle Setting

The Siren may be set to different tone setting according to your usage and application needs.
1. Press and hold 

PTT

MAN 

and 

Code 2

 for 5 seconds to enter  

Tone Cycle Setting

Code 2

 will blink 

to indicate that you are in 

Tone Cycle Setting

.

2. While in 

Tone Cycle Setting

, press 

MAN 

(-) or

 HORN

 (+) buttons to switch between different tone 

cycles. (See Siren Tone Cycle Chart) The setting is indicated with 

RADIO

SW1

SW2

SW3

 and 

SW4

 

buttons. (See Indication Chart: Tone Cycle)

PROGRAMMING

<IMPORTANT> 

When entering a setting mode, if any of the button type is not in its default setting 

(ON/OFF), an auto-clearing will be performed with a full blinking of the controller. Re-do each step 1 

to re-enter that setting mode again.

Summary of Contents for Logic 1100











Reviews: