IMJ21K-04
www.ueonline.com
SP11075K
Dimensions
Dimensional drawings for all models may be found at www.UEonline.com
Dimension A
Models
Inches
mm
NPT
127-150
8.06
204.7
1/4
S127B
8.94
227.1
1/2
S140B-S150B
8.86
225.0
1/2
232
6.53
165.9
1/4
254
6.50
165.1
1/4
357
6.88
174.8
1/4
Models 127-150
Models S127B-S150B
Model 232
Model 254
Model 357
U N I T E D E L E C T R I C
C O N T R O L S
180 Dexter Avenue, P.O. Box 9143
Watertown, MA 02471-9143 USA
Telephone: 617 926-1000 Fax: 617 926-2568
http://www.ueonline.com
RECOMMENDED PRACTICES AND WARNINGS
United Electric Controls Company recommends careful consideration of the
following factors when specifying and installing UE pressure and temperature units.
Before installing a unit, the Installation and Maintenance instructions provided
with unit must be read and understood.
• To avoid damaging unit, proof pressure and maximum temperature limits stated
in literature and on nameplates must never be exceeded, even by surges in the
system. Operation of the unit up to maximum temperature is acceptable on a
limited basis (i.e., start-up, testing) but continuous operation must be restricted to
the designated adjustable range. Excessive cycling at maximum temperature limits
could reduce sensor life.
• A back-up unit is necessary for applications where damage to a primary unit
could endanger life, limb or property. A high or low limit switch is necessary for
applications where a dangerous runaway condition could result.
• The adjustable range must be selected so that incorrect, inadvertent or
malicious setting at any range point cannot result in an unsafe system condition.
• Install unit where shock, vibration and ambient temperature fluctuations will
not damage unit or affect operation. Mount the unit so that moisture does not
enter the enclosure via the electrical connection. When appropriate, this entry
point should be sealed to prevent moisture entry.
• Unit must not be altered or modified after shipment. Consult UE if
modification is necessary.
• Monitor operation to observe warning signs of possible damage to unit, such
as drift in set point or faulty display. Check unit immediately.
• Preventative maintenance and periodic testing is necessary for critical
applications where damage could endanger property or personnel.
• For all applications, a factory set unit should be tested before use.
• Electrical ratings stated in literature and on nameplate must not be exceeded.
Overload on a switch can cause damage, even on the first cycle. Wire unit
according to local and national electrical codes, using wire size recommended in
installation sheet.
• Do not mount unit in ambient temp. exceeding published limits.
LIMITED WARRANTY
Seller warrants that the product hereby purchased is, upon delivery, free from
defects in material and workmanship and that any such product which is found to
be defective in such workmanship or material will be repaired or replaced by Seller
(Ex-works, Factory, Watertown, Massachusetts. INCOTERMS); provided, however, that
this warranty applies only to equipment found to be so defective within a period of
24 months from the date of manufacture by the Seller. Seller shall not be obligated
under this warranty for alleged defects which examination discloses are due to
tampering, misuse, neglect, improper storage, and in any case where products are
disassembled by anyone other than authorized Seller’s representatives. EXCEPT FOR
THE LIMITED WARRANTY OF REPAIR AND REPLACEMENT STATED ABOVE, SELLER
DISCLAIMS ALL WARRANTIES WHATSOEVER WITH RESPECT TO THE PRODUCT,
INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR
ANY PARTICULAR PURPOSE.
LIMITATION OF SELLER’S LIABILITY
Seller’s liability to Buyer for any loss or claim, including liability incurred in
connection with (i) breach of any warranty whatsoever, expressed or implied,
(ii) a breach of contract, (iii) a negligent act or acts (or negligent failure to act)
committed by Seller, or (iv) an act for which strict liability will be inputted to seller,
is limited to the “limited warranty” of repair and/or replacement as so stated
in our warranty of product. In no event shall the Seller be liable for any special,
indirect, consequential or other damages of a like general nature, including, without
limitation, loss of profits or production, or loss or expenses of any nature incurred by
the buyer or any third party.
UE specifications subject to change without notice.
