ABL AIP-2MBV Quick Start Manual Download Page 22

                                                                           

 

 

18 

Appendix Toxic or Hazardous Materials or Elements 

Component Name 

Toxic or Hazardous Materials or Elements 

Pb 

Hg 

Cd 

Cr VI 

PBB 

PBDE 

Circuit Board Component 

○ 

○ 

○ 

○ 

○ 

○ 

Device Construction Material 

○ 

○ 

○ 

○ 

○ 

○ 

Wire and Cable 

○ 

○ 

○ 

○ 

○ 

○ 

Power Adapter 

○ 

○ 

○ 

○ 

○ 

○ 

Packing Components 

○ 

○ 

○ 

○ 

○ 

○ 

Accessories 

○ 

○ 

○ 

○ 

○ 

○ 

 

O: Indicates that the concentration of the hazardous substance in all homogeneous materials in 

the parts is below the relevant threshold of the SJ/T11363-2006 standard. 

 

X: Indicates that the concentration of the hazardous substance of at least one of all 

homogeneous materials in the parts is above the relevant threshold of the SJ/T11363-2006 

standard. During the environmental-friendly use period (EFUP) period, the toxic or hazardous 

substance or elements contained in products will not leak or mutate so that the use of these 

(substances or elements) will not result in any severe environmental pollution, any bodily injury or 

damage to any assets.  The consumer is not authorized to process such kind of substances or 

elements, please return to the corresponding local authorities to process according to your local 

government statutes. 

 

Note: 

 

This  quick  start  guide  is  for  reference  only.  Slight  difference  may  be  found  in  user 

interface. 

 

All the designs and software here are subject to change without prior written notice.  

 

All  trademarks  and  registered  trademarks  are  the  properties  of  their  respective 

owners.  

 

If there is any uncertainty or controversy, please refer to the final explanation of us. 

 

Please visit our website or contact your local service engineer for more information. 

 

 
 

Summary of Contents for AIP-2MBV























Reviews: