manualshive.com logo in svg

Abit WI-1P, User Manual

Share
Download
Abit WI-1P User Manual Download Page 53

BIOS Setup 

3-21 

[278/IRQ5]:

 This option allows the parallel port to use [278

/

IRQ5] as its I/O port 

address. 

[3BC/IRQ7]:

 This option allows the parallel port to use [3BC

/

IRQ7] as its I/O port 

address. 

Parallel Port Mode: 

This item specifies the parallel port mode. 

[Normal]:

 Allows the standard parallel port mode to be used. 

[SPP]:

 (Standard Parallel Port) Allows bi-directional parallel port operation at normal 

speed. 

[EPP]:

 (Enhanced Parallel Port) Allows bi-directional parallel port operation at 

maximum speed. 

[ECP]

: (Extended Capabilities Port) Allows bi-directional parallel port operation at a 

speed faster than the normal mode’s data transfer rate. 

[ECP+EPP]:

 Allows parallel port operation at ECP and EPP mode. 

EPP Mode Select: 

This item selects the EPP mode. 

ECP Mode Use DMA: 

This item selects the DMA channel of the parallel port. 

User’s Manual 

Summary of Contents for WI-1P









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands