background image

11

877.788.7253  •  ABIsupport.com

ABI® Workman Trailer Manual

The ATV wiring harness has a 4-pole connector at one end and bare end wires at the other end. This har-

ness connects to the ATV’s taillight and battery.  Splice these wires, using the supplied connectors, into the 

appropriate ATV wires, as shown below. For additional assistance, please refer to your ATV owner’s manual 

or ATV wiring schematic. Seal all splices to insure that water does not corrode or short the electrical wiring.

Next route the connector-end of the wire to the rear of the ATV.  Be sure to leave enough extra wire to ac-

commodate the turning requirements when pulling your ATV Trailer.

When you are ready to use the ATV trailer, plug the connector end into the 4-pole connector at the trailer 

coupler.

Note: Some models may contain a 4-pole connector with an extra black wire. Please ignore the extra black wire.

t

o W

 V

e h I c l e

 W

I R I N G

  I

N S t a l l a t I o N

Connecting Wire  Harness To Tow Vehicle

BROWN WIRE CONNECTS TO THE VEHICLE STOP WIRE USING “A”

YELLOW WIRE CONNECTS TO VEHICLE RUNNING LIGHT WIRE USING “A”

WHITE WIRE CONNECTS TO THE VEHICLE BATTERY (-) NEGATIVE TERMINAL USING “A”

CAUTION: AN IMPROPERLY COUPLED 
TRAILER CAN RESULT IN DEATH OR SE-
RIOUS  INJURY. TIGHTEN THE  COUPLE 
ADJUSTMENT REGULARLY.

Limited Warranty For Consumers: 

ABI warrants the goods to be new and free from material defect for one 

(1) year from the date of ABI’s delivery of goods to Buyer. This warranty will be satisfied by ABI’s repairing 

the goods or furnishing replacement goods or parts, at its option. To take advantage of this warranty, Buyer 

must immediately notify ABI of the claimed defect. ABI shall have no obligation under this warranty for 

(a) goods which have been repaired or altered by any party other than ABI, and or (b) defects which result 

from misuse, accident, or improper connection of the goods to a tow vehicle, and or (c) commercial use of 

the product. THIS IS BUYER’S EXCLUSIVE REMEDY UNDER THIS WARRANTY. ABI DISCLAIMS ALL OTHER WAR-

RANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, FIT-

NESS FOR A PARTICULAR PURPOSE, AND AGAINST INFRINGEMENT. THIS WARRANTY IS NOT TRANSFERABLE.

WARNING: The trailer bed is under pressure. When 
you pull the bed latch pin, the bed will automatically 
dump. Use extreme caution or an injury could occur.

Summary of Contents for Workman













Reviews: