DECLARATION OF EU CONFORMITY
Product: SH230
Manufacturer: AB TECNO S.r.L. - Via Cicogna, 95 - 40068 San Lazzaro di Savena (BO)
The Manufacturer declares under its own responsibility that the product covered by the
declaration meets all the provisions applicable in the following Directives:
2014/35/EU - on the harmonization of the laws of the Member States relating to the making
available on the market of electrical equipment intended for use within certain voltage
limits.
2014/30/EU - for the harmonization of the laws of the Member States relating to electro-
magnetic compatibility and complies with the relevant harmonization legislation of the
Union: CEI EN 60947-1: 2008/A1: 2012/A2: 2015, CEI EN 60947-5-1: 2005/A1: 2010
Bologna, lì 01/02/2018
AB TECNO's CEO
Ulisse
Pagani
As required by the Directive 2012/19/CE concerning the Waste of Electronic and
Electrical Equipment (WEEE) it is necessary: to not dispose of WEEE as municipal
mixed waste and make a separate collection of such WEEE; contact your municipa-
lity of residence for information about the separate collection centers for
WEEE.This symbol on the electronic device indicates the separate collection of
electrical and electronic equipment (Ref. Directive 2012/19/CE). Appropriate
separate waste collection for the subsequent start-up of the disposed appliance
to environmentally compatible recycling and treatment and helps to avoid
possible negative eects on the environment and on health and favors the recycling
of the materials to which the product is composed.
TERMINAL DESCRIPTIONS
1. 230V ac power supply
2. 230V ac – power supply
3. Motor closing-
4.Motor opening-
5. Motor common-
6. +12 VDC power supply
7. -12 VDC power supply
1 2 3 4 5
6 7 8 9 10 11
IMPORTANT: Permanently connected appliances shall have
an easily accessible disconnecting device incorporated
into the wiring.
TRANSMITTER CODE MEMORIZATION
To memorize transmitter codes, the control panel must be in stable condition and the door in stop.
ONE-BUTTON MODE TRANSMITTER MEMORIZATION.
To perform memorization, press the PROG/RES programming button and release it after the beep. The red LED will light steadily, indicating that the device is
ready to memorize the transmitter code.
From this moment any code received will be memorized. Then press the button of the transmitter on which we want to activate the automatism. The red LED
will begin to flash accompanied by three beeps to confirm that the operation has been carried out correctly. After 4 seconds have elapsed since the last reception
of a code, the device will automatically exit programming with two beeps, turning off the red led.
RADIO MEMORIZATION WITH TRANSMITTER (WITH HCS TRANSMITTER ONLY).
To use this system you must have already manually memorized at least one transmitter (with HCS coding). On a previously memorized transmitter, press the
programming key or the 3 keys at the same time or key 1 and 4 of an ABEXO-type transmitter (with programmed HCS codes) to make it learn new radio
commands. As confirmation, the red LED lights up accompanied by a beep sound. Pressing a key on the new transmitter emits 3 beeps to confirm memorization.
For the 3-button version, the Stop button is pressed.
3-BUTTON MANUAL MEMORIZATION
Identical to the single-key procedure, but the Stop key must be pressed.
ERASING ALL CODES
Erasing all codes is achieved by "resetting" the memory. Press the PROG/RES key for 4 seconds. The red LED will flash several times and a series of beeps will
indicate the erasure of all previously stored codes.
EXHAUSTED MEMORY INDICATION
Having exceeded 50 stored codes, in an attempt to store new codes, the red LED will start flashing accompanied by a series of beeps for 5 seconds.
RESET
To recover the automatic operation and closing times from factory data, remove the 220V power supply and set the DIP switches to the following position:
DIP1: OFF
DIP2: ON DIP3: OFF DIPS4: ON
DIP5 - DIP6: UNAFFECTED
Remove any wires connected to terminal 9 and 4 and then power the panel to 220V.
An audible signal will warn that the process is successful. Reset the cables connected to terminal 9 and 4 and return the DIP switches to the position before the
reset process began.
EC DECLARATION OF CONFORMITY: The manufacturer declares that the product complies with the regulations required by Directives 2014/35/EU,
2014/30/EU, 2014/53/EU. At the same time, he declares that it is forbidden to put the aforementioned products into service until the machine to which they will
be incorporated or of which they will be a part is identified and declared to comply with the conditions required by Directive 89/392 EEC and the national imple-
menting legislation, i.e. until the material covered by this declaration forms a whole with the final machine.
Complete with led indicator
FLASHER connection
terminals 4 (open)
and 5 (common)
8. Safety contact - photocell input
9. Commmon
10. P. Alt. External push button input
STEP/STEP (N.O.)
11. mechanical border input or 8k2