background image

USER SETTINGS

Menu items that are followed by the greater-than (>) symbol can be adjusted. For menu 
items with read-on data (CURRENT, REACT & HEATER 1, INLET, OUTLET), the display 
returns to normal mode if no key is selected within five minutes. In other menu selections, 
the display returns to normal mode after about twenty seconds. Items lacking the (>) 
symbol are only for information and cannot be reset or adjusted.

MAIN MENU

      

Display Menu 

Press

SUBMENUS:

 Press         

MENU SELECTION

 to change the setting 

Ducting Options

A.Basic Setup

It is recommended to duct the Reactivation Outlet to an outside location.

The Reactivation ducting MUST be connected to a reactivation outlet. 
Ducting should not be longer than six meters (20 feet). Set the ducting with the 
least number of bends that can be attained.

Tips

The ducting should slope downwards away from the equipment.

Always duct the Reactivation Outlet, preferably to an outdoor location.

Notice: Sometimes, water may collect inside the Reactivation ducting.  Thus, whenever 
the ducting is moved, take care not to spill water in the machine or on the floor. 

It is recommended to duct the Reactivation Outlet to an outside location.

B.Advanced Options

Duct inlet (2) to maximize performance 

Allowing drier and colder air into the inlet increases the performance of the desiccant. 

7

8

Summary of Contents for Water Damage AbesTec 4000i











Reviews: