7
GB
MAINTENANCE
CLEANING THE PHOTOCELLS (8) (Fig. 4):
If paper particles should come to rest in the inlet
guide (for example after a paper jam) it is possible
that the machine will not turn off, due to the broken
light barrier.
To remove these paper strips and also to clean the
photocell, pass another sheet of paper through
the feed slot, or switch the machine to reverse and
wipe both „eyes“ of the photocell with a brush.
CUTTING SYSTEM MAINTANANCE:
After about 2 hours of continuous operation run
the cutting system in reverse for about 30 seconds
and, at the same time, spray some of the enclosed
special oil onto the cutting system.
ENERGY SAVING TIP:
Be certain that the machine is turned off overnight
(mains switch (1) (fig. 1) switched to „0“).
8
fig. 4
ACCESSORIES
MALFUNCTION
TAKING OUT EXCESS PAPER
IN CASE OF OVERLOAD:
If the shredder has stopped due to an overload
(motor protection) take the excess paper out of
the inlet as follows:
1. Depress the reverse pushbutton (4) (fig. 2). The
material is released.
2. Lift up the hopper. The pilot lamp „door open“ or
„hopper open“ (7) (fig. 2) will light.
3. Remove the excess material by hand from the
inlet guide.
Note: In this case, there is no danger of injury
as all circuits are interrupted when the hopper
is lifted and the machine cannot be started.
MOTOR FAULT:
The machine is equipped with a thermally protected
motor. Should this motor be overloaded, it will
switch off automatically. In such case the pilot
lamp „ready“ (5) (fig. 2) flashes.
After a cooling down period of approx. 10 minutes
(depending on the room temperature) you can
restart the machine and continue shredding.
Note: When the motor is overloaded, only the
forward run is cut off. To take the excess paper out
of the inlet opening, the cutting system may at any
time be switched on „reverse“.
FAULT CHECKLIST:
If the machine is not functioning properly, you
should check the following:
- is the plug conneted to the mains?
- is the mains switch (1) turned on?
- is the door closed?
- is the collecting bag full?
The bag has to be emptied.
- is the motor overloaded?
Please refer to the section headed „Motor Fault“.
- is there a phase failure?
Check the three-phase fuse at the power supply
socket, and replace if necessary.
If you still cannot isolate the fault after carrying
out all these checks, please notify our customer
service department.
TECHNICAL DATA
Cutting width:
802CC:
1.9x15 (cross-cut)
852CC:
3.8x40 (cross-cut)
Cutting capacity:
802CC:
35-40 sheets (70 g/m
2
)
852CC:
70-80 sheets (70 g/m
2
)
Working width:
444 mm
Power:
3.9 kW
Supply voltage:
400V/50Hz
230V/50Hz
415V/50Hz
220V/60Hz
200V/50Hz
200V/60Hz
Pre-fusing:
(gl fuse, type 1 assignment)
400V-415V/50Hz:
16 A
220V-230V/50-60Hz:
25 A
200V/50-60Hz:
25 A
Width:
750 mm
Depht:
550 mm
Height:
802CC:
1275 mm
852CC:
1600 mm
Noise level:
approx. 75 dB(A)
Weight:
802CC:
approx. 185 kg
852CC:
approx. 201 kg
Description
Order-No.
Plastic bag, 600 x 380 x 1100 x 0,6 mm
80946
Lubrication bottle, 125 ml
99943
Note: For orders of special accessories and spare parts, please contact your dealer.
Schleicher International
802CC
852CC
1-800-658-8788 - www.abcoffice.com
