ABB Zenith ZTSCT Series Operation And Maintenance Manual Download Page 7

Page: 7 / 36

ABB Zenith

ZTSCT / ZBTSCT Operation & Maintenance Manual

Installation

(cont’d)

HAZARDOUS VOLTAGE

(Can Cause Severe Injury or Death)

Turn OFF all power before installation, adjustment, or removal of transfer switch or any of its components.

DANGER

A complete information package is furnished with each

transfer switch including a complete connection diagram

and schematic which details all necessary control circuit

field connections.

The engine start control wires connect to the engine start

relay terminals located to the left of the microprocessor.

Figure 6 shows the location of these terminals.

To R/T Box

To Power Panel

Input/Output

Connectors

to I/O Modules

Engine Start

Connections

Clock Program

Backup Battery
Remove protective strip to

enable clock functions

Network Connector

Control Connections

The terminals are clearly identified by a label on the

microcontroller backplate. In the case of manual transfer

switches, or in other applications not requiring the micro-

processor, clearly marked terminal blocks are provided

in the upper left corner of the control panel for the engine

start control wires.

Figure 6

Summary of Contents for Zenith ZTSCT Series





































Search results

Summary of Contents for Zenith ZTSCT Series

Reviews:

Related manuals for Zenith ZTSCT Series

Brands by name

Popular brands

ABB Zenith ZTSCT Series, Operation And Maintenance Manual

Search results

Summary of Contents for Zenith ZTSCT Series

Reviews:

Related manuals for Zenith ZTSCT Series

Brands by name

Popular brands