manualshive.com logo in svg

ABB XIO-00, User Manual

Share
Download
ABB XIO-00 User Manual Download Page 169

 

 

XIO USER MANUAL | 2106424MNAB | 

169

 

 

Figure 8-26: Software update complete (OS and Flash) 

 

IMPORTANT NOTE:

 Updates to the main application (App) might require an update to PCCU32. 

In these cases, download a new version of PCCU32. 

8.5

 

System restart 

The XIO has several options for restart. This section provides an overview of those options and the 

corresponding procedures for manually-triggered restarts. 

 

NOTICE – Data loss

. Some of the restart procedures in this section cause customer data, device 

configuration or calibration data loss. To back up data and configuration, see section 

8.1 Preserve 

data and configuration

. 

8.5.1

 

Restart type overview 

There are several ways to restart an XIO. Restarts can be manually triggered or performed automatically 

after software updates, power removal, or other system events. Perform manually triggered restarts 

onboard or from the user interface (PCCU). 

 

Table 8-1 

describes device restarts. Review the implications of each restart type carefully to select the 

appropriate method. There may be several methods for the same type of restart. 

 

IMPORTANT NOTE:

 While there are several methods for the warm and cold restarts, ABB 

recommends restarts from PCCU32 (Entry mode or device loader).  

 

 

Summary of Contents for XIO-00
















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands