ABB XAC24061 Operation Manual Download Page 31

Page: 31 / 140

Operation Manual / 4 Product description / A100-L

Table of contents

HZTL4034_EN

Rev.R

October 2020

Product description

Introduction............................................................................................................ 4

1.1

Essential information................................................................................................... 4

1.2

Registered trademarks ................................................................................................ 4

1.3

Related documents....................................................................................................... 4

1.4

Layout and function of the turbocharger ................................................................. 5

1.5

Warning plates on the turbocharger.......................................................................... 7

1.6

Locations of the rating plates.................................................................................... 8

Removal and installation ...................................................................................... 9

2.1

Turbocharger weight ................................................................................................... 9

2.2

Removing the turbocharger........................................................................................ 9

2.3

Installing the turbocharger ....................................................................................... 11

Commissioning .................................................................................................... 14

3.1

Oil supply ....................................................................................................................... 14

3.2

Inspection procedures ................................................................................................ 14

3.3

Commissioning after taking out of operation....................................................... 16

Monitoring during operation.............................................................................. 17

4.1

Oil pressure, oil temperature..................................................................................... 17

4.2

Admissible air inlet temperature ............................................................................. 20

4.3

Turbocharger speed ................................................................................................... 20

4.4

Low pressure measurement at the filter silencer ................................................. 23

Operation and service ......................................................................................... 24

5.1

Noise emission ............................................................................................................ 24

5.2

Service work ................................................................................................................. 25

5.3

Expected replacement intervals .............................................................................. 29

5.4

Flexible turbocharger cut-out .................................................................................. 30

5.5

Stopping the engine.................................................................................................... 31

Periodic maintenance.......................................................................................... 32

6.1

Foreword to maintenance.......................................................................................... 32

6.2

Cleaning the filter silencer ........................................................................................ 33

6.3

Changing the filter strip on the filter silencer casing.......................................... 35

6.4

Cleaning the compressor during operation ........................................................... 37

6.5

Cleaning the turbine during operation.................................................................... 41

6.6

Draining the gas outlet casing ................................................................................. 45

Troubleshooting................................................................................................... 46

7.1

Malfunctions when starting...................................................................................... 46

7.2

Malfunctions during operation ................................................................................ 47

Summary of Contents for XAC24061












































































































































Search results

Summary of Contents for XAC24061

Reviews:

Related manuals for XAC24061

Brands by name

Popular brands

ABB XAC24061, Operation Manual

Search results

Summary of Contents for XAC24061

Reviews:

Related manuals for XAC24061

Brands by name

Popular brands