manualshive.com logo in svg

ABB XAC23910, Operation Manual, Page: 49 / 140

Share
Download
ABB XAC23910 Operation Manual Download Page 49

Operation Manual / 4 Product description / A100-L

4  Monitoring during operation / 4.1  Oil pressure, oil temperature

© Copyright 2020 ABB. All rights reserved.

HZTL4034_EN

Rev.R

October 2020

If the turbocharger has been operated for a longer period of time outside the admissible
range, ABB Turbocharging recommends having the turbocharger inspected by an ABB Tur-
bocharging Service Station.

4.1.1

Pre-lubrication and post-lubrication

 CAUTION

Pre-lubrication

Serious damage to engine or property can result if the turbocharger is not
supplied with oil from the first moment after starting the engine.

u

Activate the pre-lubrication device each time before starting the engine.

The pre-lubrication time is at least 5 minutes.

The post-lubrication time is at least 10 minutes.

If the engine is operated for 5 to 10 minutes in idle mode before stopping, no additional
post-lubrication is required.

Page 

19

 / 

110

Summary of Contents for XAC23910













































































































































Reviews:

No comments