background image

Disclaimers

Generic disclaimer

The manufacturer shall have no obligation hereunder with respect to any product which (i)
has been improperly repaired or altered; (ii) has been subjected to misuse, negligence or
accident; (iii) has been used in a manner contrary to the Manufacturer"s instructions; or (iv)
has failed as a result of ordinary wear and tear. All material in this manual is subject to
change without a further notice. The manual is intended as non-contractual document.

Cybersecurity disclaimer

This product is designed to be connected to and to communicate information and data via
a network interface. It is Customer's sole responsibility to provide and continuously ensure
a secure connection between the product and Customer network or any other network (as
the case may be). Customer shall establish and maintain any appropriate measures (such
as but not limited to the installation of firewalls, application of authentication measures,
encryption of data, installation of anti-virus programs, etc) to protect the product, the network,
its system and the interface against any kind of security breaches, unauthorized access,
interference, intrusion, leakage and/or theft of data or information. ABB and its affiliates are
not liable for damages and/or losses related to such security breaches, any unauthorized
access, interference, intrusion, leakage and/or theft of data or information.

Introduction to this manual 9

Summary of Contents for VSN900





































Reviews: