ABB VD4 12.06.16 p150 Installation And Service Instructions Manual Download

Page: 42 / 48

9.2.2. Stored-energy spring operating

mechanism

Carry out the functional testing of the operating

mechanism is to be performed after 5,000 oper-

ating cycles or after 4 years.

Before the test, open the circuit-breaker and carry

out the following operations:

– for withdrawable circuit-breakers, put the cir-

cuit-breaker in the isolated for test position

– for fixed circuit-breakers, cut off the power

supply to the medium voltage circuit.

Note

Insulate the working area and make it safe, fol-

lowing the safety regulations specified in the IEC/

DIN VDE Standards.

Aim of functional testing

– With the circuit-breaker disconnected from the

load, carry out several opening and closing

operations.

– Turn the power to the spring charging motor off

(if fitted) and discharge the springs by closing

and opening the circuit-breaker using the clos-

ing and opening pushbuttons.

– Visually examine the state of lubrication of the

isolating contacts, sliding surfaces, etc.

– Check correct electrical and mechanical op-

eration of the various devices (for example,

the interlocks).

9.2.3. Circuit-breaker pole

No inspection is required apart from what was

specified in par. 9.2.1.

9.3. Servicing

9.3.1. Interruption devices in general

If cleaning is found to be necessary during in-

spections as specified in par. 9.2.1., use the the

following procedure:

• insulate the working area and make it safe

by following the safety rules specified in the

IEC/DIN VDE Standards.

• general cleaning of the surfaces:

– dry and eliminate any light deposits or dirt

using a soft dry cloth;

– more resistant deposits of dirt can be re-

moved using a slightly alkaline household

cleanser or Rivolta BWR 210 type detergent.

• cleaning the insulating surfaces and conduc-

tive components:

– light dirt: with Rivolta BWR 210 detergent;

– resistant dirt: with cold 716 type detergent.

After cleaning rinse thoroughly with clean water

and dry carefully.

Note

Only use halogen-free detergents and never

1.1.1-trichloroethane, trichlorethylene or carbon

tetrachloride!

9.3.2. Actuator and transmission system

Servicing must be carried out after:

– 10,000 operations for the actuator (snap-on box)

– 15,000 operations for the shock absorber.

The other parts of the transmission system

(shaft, main levers, locking rings, etc.) are

maintenance-free up to 30,000 operations.

Note

Dismantling and replacement of the complete

operating mechanism (snap-on box) can only be

carried out by ABB personnel or by qualified and

specially trained personnel, especially for the

necessary adjustments.

Servicing details

• Turn off the spring charging motor power sup-

ply and manually discharge the operating

mechanism springs by closing and opening the

circuit-breaker.

• Replace parts subject to high climatic or

mechanical stresses after 10,000 operations

(contact an ABB service centre).

Note

These operations can only be carried out by ABB

personnel or suitably qualified and specially

trained personnel.

All manuals and user guides at all-guides.com

Summary of Contents for VD4 12.06.16 p150

















































Search results

Summary of Contents for VD4 12.06.16 p150

Reviews:

Related manuals for VD4 12.06.16 p150

Brands by name

Popular brands

ABB VD4 12.06.16 p150, Installation And Service Instructions Manual

Search results

Summary of Contents for VD4 12.06.16 p150

Reviews:

Related manuals for VD4 12.06.16 p150

Brands by name

Popular brands